Modelling, Simulation and Fault Diagnosis of the Three-Phase Inverter Using Bond Graph

González-Contreras, Brian; Lara, J.L. Rullan; Vela-Valdés, Luis Gerardo

doi:10.1109/isie.2007.4374586

Cited by 19 publications

(10 citation statements)

References 9 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…To create a model for simulation and analysis of the inverter, several authors (as [4], [5]) suggest a representation of the switching device and the reverse current diode by an equivalent circuit with two resistors and a switch (Fig. 2) When the switch is open the current flows through resistor, which has a high resistance (representing the diode).…”

Section: A Resistor -Switch Equivalent Circuitmentioning

confidence: 99%

See 1 more Smart Citation

Bond graphs representation of a Brushless DC motor and inverter driver

Simão

Roqueiro

Silva

et al. 2013

2013 Brazilian Power Electronics Conference

View full text Add to dashboard Cite

This paper present a proposal of Bond Graphs representation of a Brushless DC motor and an inverter used to drive it. The representations were developed based on previously known models. The model representations were evaluated by a simulation of reference tracking and energetics behavior. This paper provides an energetic analysis of the Bond graphs Model representation and an evaluation of the proposed models for inverter and brushless motor.

show abstract

Section: A Resistor -Switch Equivalent Circuitmentioning

confidence: 99%

“…In [4] the authors use the BG representation of the inverter as a tool for fault diagnostics of an Inverter. As is done in [5].…”

Section: Introductionmentioning

confidence: 99%

Bond graphs representation of a Brushless DC motor and inverter driver

Simão

Roqueiro

Silva

et al. 2013

2013 Brazilian Power Electronics Conference

View full text Add to dashboard Cite

show abstract

“…7, the experimental total loss P loss =P off +P on is 594W, compared with the emulational result 592W and computational result 596W using (1), (2), (3) and (4). Notice that equations (1), (2) and (3) base on one switch period, since the primary current is a sine wave and won't always in its peak value, the average power in one output period is computed as the computational result P on .…”

Section: A Snubber Performancementioning

confidence: 99%

“…Three-phase full bridge inverters, witch is constituted of three half bridge, have been deeply investigated and widely used in many medium power fields [1][2][3][4]. However, it is defective in high power fields, such as motor drivers in marine or mining, chemical industries applications, uninterrupted power supply system, etc.…”

Section: Introductionmentioning

confidence: 99%

High power combined three-phase inverter system: Analysis, design and experiments

Chen

Pan

Kang

2009

2009 IEEE 6th International Power Electronics and Motion Control Conference

View full text Add to dashboard Cite

Combined three-phase inverter is constituted of three signal H-bridge inverters. This topology has several advantages and specially suits for high power application. However, when applying combined configuration into high power application, many new features are found. These new features affect the performance of inverter system in many ways. On the viewpoint of system, these new features must be fully considered. In this paper, these features are discussed in detail. These features, which relate to system capability, model building, controller designing, protecting scheme choosing, are analyzed. Based on the analysis, the design guidelines are given. A 300kW high power inverter system with combined configuration is built. By employing the analysis and guidelines that presented in the paper, the performance, reliability and stability of the inverter system have been enhanced greatly. The further work is also proposed at the end of this paper.

show abstract

“…Considering the successful applications of bond graph in modeling electrical systems [4], mechanical systems [5], and power converters [6], there is a great potential of further utilization of bond graph in modeling the DFWPS. However, to the authors' best knowledge, fewer studies on this large and complex energy conversion system.…”

Section: Introductionmentioning

confidence: 99%

Bond graph and port-controlled hamiltonian model of doubly-fed wind power system

Song

Wang

2012

IECON 2012 - 38th Annual Conference on IEEE Industrial Electronics Society

View full text Add to dashboard Cite

Considering the energy transformation essence of doubly-fed wind power system (DFWPS), this paper proposes the use of the bond graph methodology to realize the energy representation of the DFWPS. The total bond graph, integrated by the electromechanical sub-model and the converter sub model, spans mechanical, electrical and magnetic energy do mains. Through the detailed bond graphs of sub-models and the total bond graph of the system, the corresponding port controlled Hamiltonian (PCH) models for subsystems and the whole system are also extracted. Finally, the bond graph and the PCH model of DFWPS are validated by the simulations in 20sim.

show abstract

Modelling, Simulation and Fault Diagnosis of the Three-Phase Inverter Using Bond Graph

Cited by 19 publications

References 9 publications

Bond graphs representation of a Brushless DC motor and inverter driver

Bond graphs representation of a Brushless DC motor and inverter driver

High power combined three-phase inverter system: Analysis, design and experiments

Bond graph and port-controlled hamiltonian model of doubly-fed wind power system

Contact Info

Product

Resources

About