Modelling and simulation analysis of process alternatives in the cellular manufacturing of axially symmetric parts

Siemiątkowski, Mieczysław; Przybylski, Włodzimierz

doi:10.1007/s00170-005-0366-5

Cited by 18 publications

(13 citation statements)

References 17 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Three machine alternatives, however, are included into further comparative analysis, and with reference to the specified machining features of a winch drum as the exemplary part design, and envisaged as those performed within a primary part setup (Table 1). Following the suggestions reported in [14,15], the operation alternatives are depicted in this Table by definite schemata, associated with machining the specified set of features of the primary part setup. Thus, in accordance with the reports mentioned, an individual schema is due to be understood as a technologically meaningful combination of a tool type (accordingly to a machining method) and a set of relative motions between a work part (WP) and the tool (T) of a specific geometry.…”

Section: Fig 5 Possible Placement and Orientation Of The Exemplary mentioning

confidence: 99%

Comparative Study of Machining Technology Selection to Manufacture Large-Size Components of Offshore Constructions

Deja

Siemiątkowski

Sender³

2017

Polish Maritime Research

View full text Add to dashboard Cite

The focus of this paper is on process planning for large parts manufacture in systems of definite process capabilities, involving the use of multi-axis machining centres. The analysis of machining heavy mechanical components used in off-shore constructions has been carried out. Setup concepts applied and operation sequences determined in related process plans underwent studies. The paper presents in particular a reasoning approach to setup sequencing and machine assignment in manufacturing large-size components of offshore constructions. The relevant reasoning mechanismwithin a decision making scheme on generated process plan is shown based on a case study derived from the offshore sector. Recommendations for manufacture of selected exemplary and typical parts were formulated.

show abstract

Section: Fig 5 Possible Placement and Orientation Of The Exemplary mentioning

confidence: 99%

Comparative Study of Machining Technology Selection to Manufacture Large-Size Components of Offshore Constructions

Deja

Siemiątkowski

Sender³

2017

Polish Maritime Research

View full text Add to dashboard Cite

show abstract

“…Group 5) There are also some other cases where uncertainty is considered in resource availability of production equipments where cell formation (CF) problems can be formulated by applying probability theory [10] and [11]. In addition, multi processing routes is another alternative to be substituted once a machine is faced with failure [12,13]. Group 6) Uncertainty can also be recognized in similarity coefficients.…”

Section: Published By Atlantis Pressmentioning

confidence: 99%

“…Set constraint (11) computes total processing time for each part in a cell for all scenarios. Set constraint (12) guarantees that each part must be assigned to single sequence order in each scenario. Set constraint (13) states that parts must be ordered sequentially in each cell and each scenario.…”

Section: Published By Atlantis Pressmentioning

confidence: 99%

Integrating Strategic and Tactical Decisions to Robust Designing of Cellular Manufacturing under Uncertainty: Fixed Suppliers in Supply Chain

Ghezavati

Sadjadi

Nayeri

2011

IJCIS

View full text Add to dashboard Cite

Cellular manufacturing (CM) has been identified as an innovative practice for manufacturer to achieve efficiency as well as flexibility under an uncertain environment. This study addresses a new mathematical robust model for a cellular manufacturing problem integrated with tactical aspects under supply chain network characteristics in the presence of uncertain internal parameter (processing times) and external parameter (demands). The model aims to minimize total cost consisting expected value and variance of tactical cost (scheduling), strategic cost (employment of suppliers in supply chain network) to produce exceptional elements as well as the cost of resource underutilization. The model can give up a series of the solutions that are less sensitive to the changes in input data. To solve the robust model, an efficient hybrid method based on new combination of genetic algorithm (GA), simulated annealing (SA) in a parallel structure are proposed under an optimization rule. The effectiveness of the proposed model is demonstrated by numerical results and the trade-off between solution robustness and model robustness is also analyzed.

show abstract

“…The main advantages of surface plastic working are very large to obtain a surface with low roughness, fabricating and low temperature processing, versatile tools, machine tools, and high durability. Continuous development of the technology and construction materials research suggests that the burnishing will apply and for many years [6,7,9,11].…”

Section: Introductionmentioning

confidence: 99%

The Experimental Analysis of the Burnishing Process Using the Methods – NPS

Dyl

2016

Journal of KONES. Powertrain and Transport

View full text Add to dashboard Cite

The paper presents selected results of experimental research of burnishing process of the steel tube holes. The ballizing process (NPS) is the method of burnishing where consists of pushing the tool through the hole, wherein the ball is greater in size than the opening of the value of the reduction ratio. Used tools to burnishing are hard and smooth surface. Burnishing elements are made of shape: ball, roll and disk. The ballizing process is carry out by a ball. The precise tube holes are made mostly methods abrasive machining. Machining these methods can usually maintain a within the tolerances established by the constructor size and shape and surface roughness. However, not achieved a satisfactory state surface layer of tube holes. Improve the properties of the surface layer can be obtained after application, as finishing, the slide burnishing. Modelling of the burnishing process using the method, NPS is to determine the impact of a specific curvature a rigid tool with of the workpiece. Ballizing process can increase the dimensional accuracy of tube holes, reducing the surface roughness, the strengthening of the surface layer, compressive residual stresses constitution. Compressive internal stresses substantially influence the fatigue life of machine parts. The aim of experimental research was to obtain surface layer state of compressive residual stress and the material ratio curve of convexity shape.

show abstract

Modelling and simulation analysis of process alternatives in the cellular manufacturing of axially symmetric parts

Cited by 18 publications

References 17 publications

Comparative Study of Machining Technology Selection to Manufacture Large-Size Components of Offshore Constructions

Comparative Study of Machining Technology Selection to Manufacture Large-Size Components of Offshore Constructions

Integrating Strategic and Tactical Decisions to Robust Designing of Cellular Manufacturing under Uncertainty: Fixed Suppliers in Supply Chain

The Experimental Analysis of the Burnishing Process Using the Methods – NPS

Contact Info

Product

Resources

About