Microstructures and mechanical properties of the precipitation strengthened Al0.4Cr0.7FexNi2V0.2 high entropy alloys

Shen, Qin; Huang, Daozhu; Li, Fangjie; Liu, Min; Wang, Xiaowei

doi:10.1016/j.msea.2023.144606

Cited by 7 publications

(1 citation statement)

References 40 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…It is generally believed that the initial dislocation density of the specimen determines whether residual hardening or softening is an important factor, and metal materials with lower dislocation density tend to undergo residual hardening under stronger acoustic fields. The tests in this paper used annealed bearing steel with lower dislocation density and defects, which reduced the hardness [40]. This view is consistent with the test results.…”

Section: Flow Stress Constitutive Parameters For the Cr4mo4v Bearing ...supporting

confidence: 86%

Investigation of the Flow Stress Model for Cr4Mo4V Bearing Steel under Ultrasonic Vibration Conditions

Luan,

Zhao,

Mao

et al. 2024

Metals

View full text Add to dashboard Cite

To investigate the mechanisms behind the effect of ultrasonic vibration on the plastic deformation of materials, the flow stress model of Cr4Mo4V was established according to the dislocation dynamics and thermal activation theory, which considers the effect of dislocation density evolution on plastic deformation under ultrasonic vibration conditions. The effect of amplitude and strain rate on the flow stress was analyzed by fitting the stress-strain data obtained from an ultrasonic vibration-assisted tensile (UVAT) single-factor test. To investigate the influence of strain rate and vibration duration on the acoustic effect, comparative tests with and without vibration were performed for various strain rates. The results showed that the flow stress decreased significantly in the tensile test with ultrasound compared to the test without ultrasound, and the degree of reduction increased with increasing amplitude. In addition, the nonlinear relationship between the acoustic softening effect and the strain rate was analyzed. The result demonstrates that the dislocation density absorbs the ultrasonic vibration energy, which results in slip and proliferation. Macroscopically, due to a greater susceptibility to plastic deformation, the dislocation density shows residual hardening at the end of the ultrasound. Finally, the average absolute relative error (AARE) between predicted flow stresses and experimental results under three ultrasonic conditions using the developed model were 4.49%, 1.27%, and 5.64%, which proved the validity of the model.

show abstract

Section: Flow Stress Constitutive Parameters For the Cr4mo4v Bearing ...supporting

confidence: 86%

Investigation of the Flow Stress Model for Cr4Mo4V Bearing Steel under Ultrasonic Vibration Conditions

Luan,

Zhao,

Mao

et al. 2024

Metals

View full text Add to dashboard Cite

show abstract

Tailoring the Microstructure and Mechanical Properties of Ta-Alloyed AlCoCrFeNi High-Entropy Alloys

Ren,

Chen,

Gao

et al. 2024

Metall Mater Trans A

View full text Add to dashboard Cite

A novel Fe-rich Co-free high entropy alloys with low cost and excellent comprehensive mechanical properties

Lei,

Li,

Zhang

et al. 2023

Intermetallics

View full text Add to dashboard Cite

Microstructures and mechanical properties of the precipitation strengthened Al0.4Cr0.7FexNi2V0.2 high entropy alloys

Cited by 7 publications

References 40 publications

Investigation of the Flow Stress Model for Cr4Mo4V Bearing Steel under Ultrasonic Vibration Conditions

Investigation of the Flow Stress Model for Cr4Mo4V Bearing Steel under Ultrasonic Vibration Conditions

Tailoring the Microstructure and Mechanical Properties of Ta-Alloyed AlCoCrFeNi High-Entropy Alloys

A novel Fe-rich Co-free high entropy alloys with low cost and excellent comprehensive mechanical properties

Contact Info

Product

Resources

About