Microbial desulfurization of waste latex rubber with Alicyclobacillus sp.

Chu, Yongbao; Zhao, Shuang; Wang, Yaqin; Wang, Bing‐Wu; Wei, Mei‐Ling; Hu, Minghan

doi:10.1016/j.polymdegradstab.2013.06.002

Cited by 65 publications

(29 citation statements)

References 19 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The sulphur content of the GTR surface was 0.31%. The result indicated that the GTR was partly desulfurized according to the reported literatures which the sulphur content of desulfurized GTR was 0.50 and 0.57, respectively.…”

Section: Resultssupporting

confidence: 55%

Effect of dicumyl peroxide and phenolic resin as a mixed curing system on the mechanical properties and morphology of TPVs based on HDPE/ground tire rubber

Qiao

et al. 2014

Polymer Composites

View full text Add to dashboard Cite

Thermoplastic vulcanizates (TPVs) are a special group of thermoplastic elastomer with the characteristic that consists of rubber elasticity and the processability of thermoplastic polymers. TPVs based on high density polyethylene (HDPE)/ground tire rubber (GTR) with phenolic resin (HY-2045) and dicumyl peroxide (DCP) as vulcanizing agents are prepared through dynamic vulcanization in this article. The blends consisting of 40/60 HDPE/GTR are melt-mixed in an internal mixer and then pressed with a compression molding machine. The aim of this experiment is to study the influence of a compound curing agent system on the mechanical properties of the HDPE/GTR composites. The results indicate that the mechanical properties of the HDPE/GTR blends are improved significantly by adding 4 phr HY-2045 and 0.3 phr DCP than those of TPVs without any vulcanizing agents after dynamic vulcanization. The X-ray photoelectron spectroscopy study and the FTIR-ATR analysis confirmed that the crosslinking phenomenon occurred in the preparation of TPVs; and the gel fraction analysis indicates that the GTR components and the HDPE components of the HDPE/GTR blends are all moderately crosslinked.

show abstract

Section: Resultssupporting

confidence: 55%

Effect of dicumyl peroxide and phenolic resin as a mixed curing system on the mechanical properties and morphology of TPVs based on HDPE/ground tire rubber

Qiao

et al. 2014

Polymer Composites

View full text Add to dashboard Cite

show abstract

“…2c, curve b), which can be ascribed to the C]O, C]N and N-H groups, respectively, 26,39,40 verifying the oxidation and polymerization of TEPA. Additionally, another new absorption peak could also be observed at around 1120 cm À1 , which was associated with the stretching vibrations of the S]O bond derived from Na 2 S 2 O 8 , 41 and indicated the successful doping of sulphur into N, S-codoped CDs. The compositions of the as-synthesized CDs were further analysed using XPS spectra.…”

Section: Characterization Of the As-prepared N S-codoped Cdsmentioning

confidence: 92%

Carbon source self-heating: ultrafast, energy-efficient and room temperature synthesis of highly fluorescent N, S-codoped carbon dots for quantitative detection of Fe(iii) ions in biological samples

et al. 2020

View full text Add to dashboard Cite

show abstract

“…MAH, which has anhydride groups, was an additive used in study on the photo-grafting reaction and solution state-grafting reaction. [11][12][13][14][15] Kiatkamjornwong et al 16,17 and Goncalvesets et al 18 used MAH as a grafting agent without initiator in bulk state. Manufactured MAH-g-PP was analyzed by FTIR-ATR (Nicolet Instrument Co., USA).…”

Section: Preparation Of Functionalized Epdm Powders and Ppmentioning

confidence: 99%

Study on the Functionalization of Waste EPDM and PP Blend

Chung¹,

Kim²

2015

Elastomers and Composites

View full text Add to dashboard Cite

Recycling of ethylene-propylene-diene terpolymer (EPDM) scrap was tried by blending with polypropylene (PP). EPDM scrap powder was prepared by shear pulverization process at high temperature, which may lead to selective chain scission induced by difference in the critical elastic coefficient. On the other hand, EPDM scrap powder was prepared by adding a selected reclaiming agent during shear pulverization process at high temperature. Terpene as a bonding agent was then introduced to improve adhesion property. PP, used as a matrix for manufacturing thermoplastic elastomer, was modified by the incorporation of dicumyl peroxide and maleic anhydride. The functionalized EPDM and modified PP were blended and cured dynamically at 190 o C. The blend materials prepared in this study showed the comparable results to those of conventional TPE in terms of tensile and flow properties. Also, the odor component of recycled EPDM was analyzed using GC-MS.

show abstract

Microbial desulfurization of waste latex rubber with Alicyclobacillus sp.

Cited by 65 publications

References 19 publications

Effect of dicumyl peroxide and phenolic resin as a mixed curing system on the mechanical properties and morphology of TPVs based on HDPE/ground tire rubber

Effect of dicumyl peroxide and phenolic resin as a mixed curing system on the mechanical properties and morphology of TPVs based on HDPE/ground tire rubber

Carbon source self-heating: ultrafast, energy-efficient and room temperature synthesis of highly fluorescent N, S-codoped carbon dots for quantitative detection of Fe(iii) ions in biological samples

Study on the Functionalization of Waste EPDM and PP Blend

Contact Info

Product

Resources

About