Micro-strip Patch 2.4 GHz Wi-Fi Antenna Design For WLAN 4G- 5G Application

DEMIRBAS, Gokcen; Göçen, Cem; Akdag, Ismail

doi:10.46291/icontechvol6iss1pp68-72

Cited by 8 publications

(2 citation statements)

References 7 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…When making a micro-strip antenna, there are three important parts to think about: the ground, the patch, and the substrate. To begin designing the antenna, the first thing that must be done is to create the ground layer, also known as the conducting layer [19]. Copper is used for the antenna's grounding material, and its thickness is 0.0035 mm.…”

Section: Proposed Antenna Design and Simulation Resultsmentioning

confidence: 99%

Microstrip patch antenna design and simulation for S-band wireless applications operating at 3.5 GHz

Rana,

Fahim,

Ghosh

et al. 2023

Bulletin EEI

View full text Add to dashboard Cite

In the modern world, wireless technology is one way to send information from one place to another. This technology is getting better and better with time, which significantly impacts the activities that make up daily living. This wireless application has the most impact on mobile and other technologies. This research paper shows the design and analysis of a 3.5 GHz microstrip patch antenna (MPA) for wireless applications. The substrate material is Roggers RT/duroid, which has a dielectric permittivity of 2.2 computer simulation technology (CST) software does antenna design and simulation. Some observed parameters are the S-parameter, antenna directivity gain, voltage standing wave ratio (VSWR), and bandwidth. From the simulation, the return loss, VSWR, directivity gain, and bandwidth are -50.4227, 1.0061, 7.43 dBi, and 122.1 MHz respectively. This study aims to find the best return loss, get the most directional gain, and get the VSWR closer to 1. When this antenna was used, the results were better than those in scientific journals and conferences. As a result, this antenna is anticipated to fulfill the requirements of various wireless communication applications effectively.

show abstract

Section: Proposed Antenna Design and Simulation Resultsmentioning

confidence: 99%

Microstrip patch antenna design and simulation for S-band wireless applications operating at 3.5 GHz

Rana,

Fahim,

Ghosh

et al. 2023

Bulletin EEI

View full text Add to dashboard Cite

show abstract

“…According to Demirbas et al [17] an antenna has been built with a frequency of 2.4 GHz. This antenna could be used in the next generation of wireless communication systems, which are in high demand now because technology is improving.…”

Section: Literature Reviewmentioning

confidence: 99%

A 2.45 GHz microstrip patch antenna design, simulation, and anlaysis for wireless applications

et al. 2023

View full text Add to dashboard Cite

This paper designs, simulates, and analyzes the S-band microstrip patch antenna (MPA) for wireless applications. FR-4 (lossy) and Rogger RT/duroid, whose dielectric permittivity is 4.3 and 2.2, respectively, have been used as substrate materials. Simulation is done by computer simulation technology (CST) suite studio 2019 software. Simulations with FR-4 material showed that the return loss was -20.405 dB, the gain was 2.592 dB, the directivity was 7.47 dBi, the voltage standing wave ratio (VSWR) was 1.221, the bandwidth (BW) was 0.0746 GHz, and the efficiency was 34.69%. Also, Rogers RT/duroid material gives results of a return loss of -12.542 dB, a bandwidth (BW) of 0.0349 GHz, a gain of 8.092 dB, a directivity of 8.587 dBi, and an efficiency of 94.24%. The main goal of this antenna is to have a low return loss while getting as close as possible to a VSWR of 1. This will improve the antenna's gain, directivity, and efficiency compared to other antennas. Copper was used to make the patch and the ground, which were 0.35 mm and 0.0077 mm thick, respectively. The results obtained from the proposed antenna were better than those previously published in various in modern scientific journal and conference papers.

show abstract