Abstract:Rotary friction welding (RFW) is a green manufacturing technology with environmental pollution in the field of joining methods. In practice, the welding quality of the friction-welded parts was affected by the peak temperature in the weld joint during the RFW of dissimilar plastic rods. In industry, polycarbonate (PC) and acrylonitrile butadiene styrene (ABS) are two commonly used plastics in consumer products. In this study, the COMSOL multiphysics software was employed to estimate the peak temperature in the… Show more
“…This result shows that the welding quality of the RFW of PC and ABS dissimilar rods is robust. It should be noted that the fractured location appears in the ABS rods after the fatigue test, which is same as the bending test [ 32 ].…”
Understanding the fatigue behaviors of weld joints is significant in engineering practice. Rotary friction welding (RFW) can join the additively manufactured polymer components. Until now, no research has focused on the fatigue behavior of polymer components jointed via RFW. This study investigates the fatigue life of ABS/PC dissimilar components fabricated via RFW and proposes the fatigue mechanism based on the failure structure. This work uses five different cyclic loads and rotational speeds to investigate the fatigue life. The fatigue life of the RFW of ABS/PC dissimilar rods is better compared with the pure ABS and pure PC specimens due to weld and integrity microstructural changes resulting from the combination of ABS and PC materials. The number of cycles until the rupture of RFW of ABS/PC dissimilar components (y) can be determined by the cyclic load (x) according to the prediction equation of y = −838.25x2 − 2035.8x + 67,262. The fatigue life of the RFW of ABS/PC dissimilar components increase with the increased rotational speed. The number of cycles until rupture (y) can be determined by the different rotational speeds (x) according to the prediction equation of y = 315.21x2 + 2710.4x + 32,124.
“…This result shows that the welding quality of the RFW of PC and ABS dissimilar rods is robust. It should be noted that the fractured location appears in the ABS rods after the fatigue test, which is same as the bending test [ 32 ].…”
Understanding the fatigue behaviors of weld joints is significant in engineering practice. Rotary friction welding (RFW) can join the additively manufactured polymer components. Until now, no research has focused on the fatigue behavior of polymer components jointed via RFW. This study investigates the fatigue life of ABS/PC dissimilar components fabricated via RFW and proposes the fatigue mechanism based on the failure structure. This work uses five different cyclic loads and rotational speeds to investigate the fatigue life. The fatigue life of the RFW of ABS/PC dissimilar rods is better compared with the pure ABS and pure PC specimens due to weld and integrity microstructural changes resulting from the combination of ABS and PC materials. The number of cycles until the rupture of RFW of ABS/PC dissimilar components (y) can be determined by the cyclic load (x) according to the prediction equation of y = −838.25x2 − 2035.8x + 67,262. The fatigue life of the RFW of ABS/PC dissimilar components increase with the increased rotational speed. The number of cycles until rupture (y) can be determined by the different rotational speeds (x) according to the prediction equation of y = 315.21x2 + 2710.4x + 32,124.
“…Two different phenomena were found. One is that the HAZ width increases with increasing rotational speeds due to peak welding temperature [33]. This significant change can be attributed to the changes in different peak temperatures.…”
Rotary friction welding (RFW) has no electric arc and the energy consumption during welding can be reduced as compared with conventional arc welding since it is a solid-phase welding process. The RFW is a sustainable manufacturing process because it provides low environmental pollution and energy consumption. However, few works focus on the reliability of dissimilar polymer rods fabricated via RFW. The reliability of the frictionally welded components is also related to the ambient temperatures. This work aims to investigate the effects of ambient temperature on the mechanical properties of frictionally welded components of polycarbonate (PC) and acrylonitrile butadiene styrene (ABS) dissimilar polymer rods. It was found that the heat-affected zone width increases with increasing rotational speeds due to peak welding temperature. The Shore A surface hardness of ABS/PC weld joint does not change with the increased rotational speeds. The Shore A surface hardness in the weld joint of RFW of the ABS/PC is about Shore A 70. The bending strength was increased by about 53% when the welded parts were placed at 60–70 °C compared with bending strength at room temperature. The remarkable finding is that the bending fracture position of the weldment occurs on the ABS side. It should be pointed out that the bending strength can be determined by the placed ambient temperature according to the proposed prediction equation. The impact energy was decreased by about 33% when the welded parts were placed at 65–70 °C compared with the impact energy at room temperature. The impact energy (y) can be determined by the placed ambient temperature according to the proposed prediction equation. The peak temperature in the weld interface can be predicted by the rotational speed based on the proposed equation.
“…The macrostructure of the welded joint was investigated using optical microscopy (OM) (Quick Vision 404, Mitutoyo Inc., Tokyo, Japan). The bending strength of the welded parts was investigated using a threepoint bending test machine (RH-30, Shimadzu Inc., Kyoto, Japan) with a movement speed of about 1 mm/s [28]. Figure 4 shows the experimental setup for the surface hardness and bending strength of the frictionally welded parts.…”
Three-dimensional printing is widely used for manufacturing a variety of functional components. However, the 3D printing machine substantially limits the size of the functional components. Rotary friction welding (RFW) is a possible solution to this problem. In addition, there is a notable scarcity of research directed toward the domain knowledge of RFW involving dissimilar polymer rods containing metal powder. In this study, two welding specimens fabricated by polylactic acid (PLA)-containing copper powder and PLA-containing aluminum powder were joined using a turning machine. After RFW, a bending test and a Shore A surface hardness test were performed to investigate the weld quality. It was found that the bending strength of the welded parts fabricated by RFW of PLA and PLA-containing Al powder rods can be enhanced by about 57.5% when the welded part is placed at 45 °C. Surface hardness test results showed that the surface hardness of the weld interface is better than that of the 3D printed parts, and the average surface hardness of the weld interface from RFW of PLA and PLA is the highest. The surface hardness of the weld joint is about 3% higher than that of the base material. The surface hardness of the heat-affected zone is about 3% lower than that of the base material. The average peak temperature of the welded joint is the highest in the RFW of PLA-containing Al powder and PLA-containing Al powder rods. The average peak temperature of the weld joint can be as high as 160 °C. The average peak temperature of the welded joint is the highest in the RFW of PLA-containing Cu powder and PLA-containing Cu powder rods. The average peak temperature of the welded joint can be as high as 144 °C. A technical database was built for the selection of ambient temperatures used for the RFW of dissimilar polymer rods containing metal powder and three base materials.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.