Mechanical behavior and semiempirical force model of aerospace aluminum alloy milling using nano biological lubricant

Duan, Zhenjing; Li, Changhe; Zhang, Yanbin; Yang, Min; Gao, Teng; Liu, Xin; Li, Runze; Said, Zafar; Debnath, Sujan; Sharma, Shubham

doi:10.1007/s11465-022-0720-4

Cited by 59 publications

(9 citation statements)

References 65 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The lowest contact angle was also observed, indicating that the optimal tribological properties occurred with the 0.5 wt% Al 2 O 3 concentrated cotton seed nanofluid milling of 45 steel. Duan et al [36] studied the mechanical properties of aerospace aluminium alloy milling employing nano-biological lubricant. Using a designed single-factor experiment, nanofluid minimal quantity lubrication (NMQL) and the milling feed factor were introduced into the instantaneous milling force coefficient.…”

Section: Introductionmentioning

confidence: 99%

Performance assessment of some selected vegetable oils as lubricants in turning of AISI 1045 steel using a Taguchi-based grey relational analysis approach

Abegunde,

Kazeem,

Akande

et al. 2023

Tribology - Materials, Surfaces & Interfaces

View full text Add to dashboard Cite

This study is focused on the performance evaluation of three cutting lubricants, which are neem, palm kernel and mineral oil in the turning of AISI 1045 with MQL. Optimization of machining parameters with multi-response signals using Taguchi-based grey relational analysis was done. For experimental design, tests were developed using Taguchi's L 9 orthogonal array and the signal-to-noise ratio was obtained using the smaller-the-better approach to achieve the optimal combination. Performance indicators including surface roughness and cutting temperature were measured throughout the machining process. Neem oil performed best among the oils for surface roughness while mineral oil outperformed them all for cutting temperature, according to the experimental results. The optimum spindle speed, feed rate and depth of cut for neem, palm kernel and mineral oils are 870 rev/min, 0.25 mm/rev and 1.25 mm; 870 rev/min, 0.10 mm/rev and 0.75 mm; and 415 rev/min, 0.10 mm/rev and 1.00 mm, respectively.

show abstract

Section: Introductionmentioning

confidence: 99%

Performance assessment of some selected vegetable oils as lubricants in turning of AISI 1045 steel using a Taguchi-based grey relational analysis approach

Abegunde,

Kazeem,

Akande

et al. 2023

Tribology - Materials, Surfaces & Interfaces

View full text Add to dashboard Cite

show abstract

“…27 ). From all these scenarios of experimental results, it can be revealed that higher concentrations of nanoparticle have fulfilled the objective function for minimization of temperature, roughness, tool wear, CRC and coefficient of friction [ [70] , [71] , [72] ]. Moreover, the objective to maximize the shear angle has also been achieved at 1.5% NC.…”

Section: Resultsmentioning

confidence: 99%

A novel study on the influence of graphene-based nanofluid concentrations on the response characteristics and surface-integrity of Hastelloy C-276 during minimum quantity lubrication

Singh,

Sharma,

Seikh

et al. 2023

Heliyon

View full text Add to dashboard Cite

“…Cryogenic Minimum Quantity Lubrication (CMOL) is a novel lubrication system that combines low-temperature cooling technology with MQL technology. Its cooling media include liquid nitrogen, liquid carbon dioxide, cold air, and supercritical carbon dioxide [82]. LN2, as a cooling medium, can reach −196 °C at atmospheric pressure, and its effectiveness is notable [83].…”

Section: Cryogenic Mql Processing Of Nickel-based Alloysmentioning

confidence: 99%

Research Status and Prospect of Ultrasonic Vibration and Minimum Quantity Lubrication Processing of Nickel-based Alloys

Gu,

Wang,

et al. 2024

Intelligent and Sustainable Manufacturing

View full text Add to dashboard Cite

Nickel-based alloys has important application value in modern industrial field, but there are a lot of problems that are difficult to solve in traditional processing, and it is a typical difficult-to-process material. In order to improve the machinability of nickel-based alloys, scholars try to use a variety of non-traditional processing methods to explore and study the processing of nickel-based alloys. In these studies, ultrasonic vibration assisted processing technology and minimum quantity lubrication (MQL) processing technology can achieve remarkable results. The intermittent separation cutting characteristics of ultrasonic vibration assisted processing technology can improve the processing quality by changing the tool path, while minimum quantity lubrication processing technology can improve the lubrication effect of cutting, combining ultrasonic vibration assisted MQL processing leverages the benefits of both methods, resulting in improved machinability and expanded application of nickel-based alloys. Summarize the current research status on the machining mechanism of nickel-based alloys assisted by ultrasonic vibration and micro lubrication, and anticipate its developmental trends. This provides a reference for future research on the efficient machining mechanisms and practical applications of nickel-based alloys.

show abstract

Mechanical behavior and semiempirical force model of aerospace aluminum alloy milling using nano biological lubricant

Cited by 59 publications

References 65 publications

Performance assessment of some selected vegetable oils as lubricants in turning of AISI 1045 steel using a Taguchi-based grey relational analysis approach

Performance assessment of some selected vegetable oils as lubricants in turning of AISI 1045 steel using a Taguchi-based grey relational analysis approach

A novel study on the influence of graphene-based nanofluid concentrations on the response characteristics and surface-integrity of Hastelloy C-276 during minimum quantity lubrication

Research Status and Prospect of Ultrasonic Vibration and Minimum Quantity Lubrication Processing of Nickel-based Alloys

Contact Info

Product

Resources

About