Laser Welding of New Grade of Advanced High Strength Steel STRENX 1100 MC

Detailed studies on microstructure-property relationships of thermomechanically processed medium-Mn steels with various manganese contents were carried out. Microscopic techniques of different resolution (LM, SEM, TEM) and X-Ray diffraction methods were applied. Static tensile tests were performed to characterize mechanical properties of the investigated steels and to determine the tendency of retained austenite to strain-induced martensitic transformation. Obtained results allowed to characterize the microstructural aspects of strain-induced martensitic transformation and its effect on the mechanical properties. It was found that the mechanical stability of retained austenite depends significantly on the manganese content. An increase in manganese content from 3.3% to 4.7% has a significant impact on the microstructure, stability of γ phase and mechanical properties of the investigated steels. The initial amount of retained austenite was higher for the 3Mn-1.5Al steel in comparison to 5Mn-1.5%Al steel-17% and 11%, respectively. The mechanical stability of retained austenite is significantly affected by the morphology of this phase. case, the phase transformation kinetics depends significantly on the austenite deformation degree [5,8,9]. In case of the first generation AHSSs, the main advantage of the TMP is the ability to refine the ferrite grain size by controlling the austenite pancaking [10,11]. Moreover, the thermomechanical treatment can increase the amount of retained austenite to obtain the optimal TRIP (TRansformation Induced Plasticity) effect [12,13]. In case of medium manganese steels (third generation AHSS), the TMP is also a good alternative for the cold-rolling process [14][15][16]. However, most publications on medium-Mn steels concern the cold-rolling process and subsequent inter-critical heat treatment.Cold-rolled medium-Mn TRIP steels are susceptible to plastic instabilities associated with dynamic strain aging (DSA) and serrated flow (PLC-Portevin-Le Chatelier) effects due to the heat treatment required after cold-rolling. From a technological point of view, the PLC and DSA effects must be avoided. The DSA phenomenon gives rise to non-homogeneous plastic flow during the sheet-forming processes and may lead to surface defects on formed parts [17][18][19]. Our previous reports on thermomechanically processed medium-Mn sheet steels indicate that the problem can be avoided [7].Newly developed fine-grained ferrite-austenite or bainitie-austenite steels contain manganese in a range of 3-12%, while carbon content is ca. 0.1-0.2%. These steels contain also aluminum and silicon (1-3%) additions which delay the carbides formation during the bainitic transformation. The increased Mn amount leads to obtain the high fraction of retained austenite (~10-30%). The Mn addition also increases the carbon solubility and lowers the cementite precipitation temperature [20][21][22]. Al is added to partially replace silicon due to the problems related to galvanizing, hot-rolling and welding [23][24][25]. However, Gir...

Section: Chemical Compositionmentioning

confidence: 99%

mentioning

confidence: 99%

Microstructure–Property Relationships in Thermomechanically Processed Medium-Mn Steels with High Al Content

Grajcar

Kilarski²,

Kozłowska

2018

“…The authors state that the narrow width of this area does not significantly affect the mechanical properties of welded joints. However, it appears that, particularly in cases of steels characterised by a high yield point, this area could develop sensitisation to brittle and fatigue cracking and the reduction of plastic properties [13][14][15][16][17]. In the initial state, steels subjected to the thermomechanical control process have a fine-grained structure additionally hardened through straining.…”

Section: Introductionmentioning

confidence: 99%

Assessment of Steel Subjected to the Thermomechanical Control Process with Respect to Weldability

Górka

2018

Abstract:The study is concerned with the assessment of the weldability of steel S700MC subjected to the thermomechanical control process (TMCP) and precipitation hardening and characterised by a high yield point. Appropriate mechanical and plastic properties of steel S700MC were obtained using the thermomechanical control process through precipitation, solution, and strain hardening as well as by using grain-refinement-related processes. Constituents responsible for the hardening of steel S700MC include Ti, Nb, N, and C. The hardening is primarily affected by (Ti,Nb)(C,N)-type dispersive precipitates sized from several nanometres to between ten and twenty nanometres. The welding process considerably differs from TMCP conditions, leading to the reduction of plastic properties both in the heat-affected zone (HAZ) and in the weld area. This study demonstrates that in cases of TMCP steels, where the effect of precipitation hardening is obtained through titanium and niobium hardening phases, the carbon equivalent and phase transformation γ-α cannot constitute the basis of weldability assessment. The properties of welded joints made from the above-named group of steels are primarily affected by the stability of hardening phases, changes in their dispersion, and ageing processes. The most inferior properties were identified in the high-temperature and coarse-grained HAZ area, where the nucleation of hardening phases in the matrix and their uncontrolled reprecipitation in the fine-dispersive form lead to a sharp decrease in toughness.

“…">MaterialThe chemical composition of the investigated steel is shown in Table 1. It is well-known [32,33] that an increased carbon content deteriorates the steel weldability. Moreover, the probability of the occurrence of the PLC effect becomes higher [19].…”

mentioning

confidence: 99%

Effect of Deformation Temperature on the Portevin-Le Chatelier Effect in Medium-Mn Steel

Grzegorczyk

Kozłowska

Morawiec

et al. 2018

Experimental investigations of the plastic instability phenomenon in a hot-rolled medium manganese steel were performed. The effects of tensile deformation in a temperature range of 20-140 • C on the microstructure, mechanical properties, and flow stress serrations were analyzed. The Portevin-Le Chatelier (PLC) phenomenon was observed for the specimens deformed at 60 • C, 100 • C, and 140 • C. It was found that the deformation temperature substantially affects the type and intensity of serrations. The type of serration was changed at different deformation temperatures. The phenomenon was not observed at room temperature. The plastic instability occurring for the steel deformed at 60 • C was detected for lower strain levels than for the specimens deformed at 100 • C and 140 • C. The increase of the deformation temperature to 100 • C and 140 • C results in shifting the PLC effect to a post uniform deformation range. The complex issues related to the interaction of work hardening, the transformation induced plasticity (TRIP) effect, and the PLC effect stimulated by the deformation temperature were addressed. stabilize the retained austenite through its carbon enrichment [8]. An alternative approach is to apply thermomechanical processing (TMP) as direct one-step cooling following the hot rolling. The TMP has the potential for energy savings and high productivity due to the elimination of the need for successive heating [9][10][11]. Chemical composition and processing parameters are designed to obtain the optimal TRIP (Transformation Induced Plasticity) effect, which ensures superior mechanical properties [12,13].Besides the many advantages of this group of steels, some problems during their processing can occur. Medium manganese steels [14-17] and high manganese steels [18][19][20] are prone to plastic instabilities phenomena associated with a serrated flow behavior-Portevin-Le Chatelier (PLC) effect and the appearance of Lüders bands. This is especially the case for cold-rolled steel sheets [21]. Moreover, it critically depends on the carbon level. With a higher C content, a pronounced effect is more visible. The heterogeneous deformation related to the increase in flow stress can lead to numerous cracks during the forming of sheets. Moreover, delayed cracking after deep drawing can appear. Delayed cracking is mostly observed in high-Mn content steels of the high austenite volume fraction. With the increased volume fraction of (retained) austenite, hydrogen embrittlement may be a more important concern. TWIP steels in the last decades have displayed important delayed cracking, which was industrially solved by decreasing the C content, Al alloying, and/or metallurgical processing [22,23]. Medium Mn steels have a less pronounced problem of delayed cracking compared to high-Mn steels [24,25].The PLC effect is commonly known as characteristic serrations which can be observed on a strain-stress curve during a tensile test. The PLC effect has not been fully characterized yet. However, some correlations between the TRIP a...