Large strain creep analysis of thick-walled cylinders

Bhatnagar, N. S.; Arya, Vinod K.

doi:10.1016/0020-7462(74)90004-3

Cited by 39 publications

(15 citation statements)

References 10 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…A nice agreement is noticed in Figure 4 between the stresses estimated by following the current procedure and those reported (Bhatnagar and Arya, 1974), thus inspiring the confidence in FE modeling and analysis procedures used in the study.…”

Section: Validationsupporting

confidence: 79%

“…To accomplish this task, the radial and tangential stresses were estimated in a monolithic cylinder for which the results are reported by Bhatnagar and Arya (1974). The dimensions, creep parameters and operating conditions of the cylinder are listed as follows:…”

Section: Validationmentioning

confidence: 99%

“…Radial (Bhatnagar and Arya, 1974) Tangential (Current) Figure 4. Stresses in monolithic cylinder the material property such as Young's modulus also decreases with radius ( Figure 6).…”

Section: Radial (Current)mentioning

confidence: 99%

See 2 more Smart Citations

FE modeling of creep in linear and non-linear FGM cylinder under internal pressure

Garg

Deepak

Gupta

2014

Multidiscipline Modeling in Materials and Structures

View full text Add to dashboard Cite

Purpose -The purpose of this paper is to investigate creep in an internally pressurized thick-walled, closed ends cylinder made of functionally graded composite, having linear and non-linear distribution of reinforcement, using finite element (FE) analysis. Design/methodology/approach -FE-based Abaqus software is used to investigate creep behavior of a functionally graded cylinder. The cylinder is made of composite containing linear and non-linearly varying distributions of reinforcement along the radius. The creep behavior has been described by Norton's power law. The creep stresses and strains have been estimated in linear and non-linear functionally graded materials (FGM) cylinders and compared with those estimated for a similar composite cylinder but having uniform distribution of reinforcement. Findings -The radial stress in the composite cylinder is observed to decreases over the entire radius upon imposing linear or non-linear reinforcement gradients. However, the tangential stress in the cylinder increases near the inner radius but decreases toward the outer radius, on imposing linear or non-linear reinforcement gradients. The creep strains in the FGM cylinders are significantly lower than those observed in a uniform composite cylinder. Originality/value -The creep strains in an internally pressurized functionally graded thick composite cylinder could be reduced significantly by employing non-linear distribution of reinforcement along the radial direction.

show abstract

Section: Validationsupporting

confidence: 79%

Section: Validationmentioning

confidence: 99%

See 1 more Smart Citation

FE modeling of creep in linear and non-linear FGM cylinder under internal pressure

Garg

Deepak

Gupta

2014

Multidiscipline Modeling in Materials and Structures

View full text Add to dashboard Cite

show abstract

“…The creep-behavior is treated for example by BAILEY (1935), DAVIS (1960), RIMROTT (1959), RIMROTT, MILLS and MARIN (1960), BESSELING (1962), ODQUIST and HULT (1962), ODQUIST (1966), MARIOTT (1972), FAIRBAIRN and MACKIE (1972), ZYCZKOWSKI and SKRZYPEK (1972), PENNY and MARIOTT (1971), SETH (1972), BHAT-NAGAR andARYA (1974), andHULT (1974). The creep-behavior is treated for example by BAILEY (1935), DAVIS (1960), RIMROTT (1959), RIMROTT, MILLS and MARIN (1960), BESSELING (1962), ODQUIST and HULT (1962), ODQUIST (1966), MARIOTT (1972), FAIRBAIRN and MACKIE (1972), ZYCZKOWSKI and SKRZYPEK (1972), PENNY and MARIOTT (1971), SETH (1972), BHAT-NAGAR andARYA (1974), andHULT (1974).…”

Section: Creep Behavior Of Thick-walled Tubesmentioning

confidence: 99%