Kinetics of Structure Formation in the Heating of Cold-Rolled Automotive Steel Sheet

Vasilyev, A.; Колбасников, Н. Г.; Rudskoy, A. I.; Sokolov, D. F.; Sokolov, S. F.

doi:10.3103/s0967091217120130

Cited by 5 publications

(3 citation statements)

References 15 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Determination of extreme values of parameters of formation of protective and decorative coating with water-dispersion compositions was made using the method of steep ascent [8].…”

Section: Resultsmentioning

confidence: 99%

“…As shown by the analysis of the results of the studies presented in figure 4, the increase in the percentage of dry residue is directly proportional to the concentration of the injected pigment and varies from 24 to 36 %, and the size of the pigment particles affects this indicator slightly (2-3%). During the filling of paint pigments the main qualitative properties of the obtained coating composition is hiding power of paint [6].…”

Section: New Materials and Technologies In Mechanical Engineeringmentioning

confidence: 99%

See 1 more Smart Citation

Improvement of Technology of Formation of Coatings with Metal Effect by Modified Water-Dispersion Paints

Соколова

Markov

Rzhavtsev

2019

KEM

View full text Add to dashboard Cite

The work is devoted to the study of the formation of protective and decorative coatings environmentally safe combined paint compositions. The considered work covers a range of issues related to colloidal-chemical modification of organo-soluble and water-dispersion lacquer compositions, development of their rational formulations and finishing modes, study of physical, mechanical and operational properties of protective coatings and ends with the calculation of the possible economic efficiency of the research results. In work environmentally safe water-dispersive paint and varnish compositions for transparent and opaque finishing by method of colloidal-chemical modification are developed. Optimal conditions for obtaining combined water-dispersion lacquer compositions of pigmented and non-pigmented and finishing modes are established. Modification of paint compositions with metal pigments allows to obtain a glazing coating, which significantly expands the color gamut of protective and decorative coatings.

show abstract

“…Determination of extreme values of parameters of formation of protective and decorative coating with water-dispersion compositions was made using the method of steep ascent [8].…”

Section: Resultsmentioning

confidence: 99%

Section: New Materials and Technologies In Mechanical Engineeringmentioning

confidence: 99%

Improvement of Technology of Formation of Coatings with Metal Effect by Modified Water-Dispersion Paints

Соколова

Markov

Rzhavtsev

2019

KEM

View full text Add to dashboard Cite

show abstract

“…A simple hanging is used to produce curved short shells of considerable double curvature of biconvex form with large angles of coverage up to 180 °. Tension presses type OP have a horizontal table with the arrangement of clamps along its side (long) sides (Miheev et al, 2003;Grechnikov et al, 2009;Vasilyev et al, 2017;Baimova et al, 2017;Stepanov et al, 2017). In the overwhelming majority of these presses have a lifting table, by moving it and tightening is done at fixed clamps (press OP-3).…”

Section: Introductionmentioning

confidence: 99%

The System of Informational Choice of the Kinematic Scheme for the Formation of Shells of a Complex Spatial Form

Mikheev¹,

Grechnikova²,

Roslyakov³

et al. 2019

Int J Math, Eng, Manag Sci

View full text Add to dashboard Cite

Three kinematic schemes are studied, which differ from one another in the route of technological operations. Each of these kinematic schemes has its own set of power stages of shaping and stages of free bending or bending of the ends of the sheet blank. In addition, the quantitative values of the angular parameters of a particular kinematic scheme are determined. Numerical experiments have been carried out, which give complete information about the distribution of the shell thickness as discrete values in one or another element. The result is statistical processing of this information, the scope of the predicted values and comparison with the tolerance on the thickness of the peel used in aviation enterprises.

show abstract

Data Management for Solving the Problem of Sequential Shaping Simulation

Mikheev

Grechnikova

Agafonova

et al. 2019

IOP Conf. Ser.: Mater. Sci. Eng.

View full text Add to dashboard Cite

The publication presents the results of a study of the process of investing in the innovation of the Russian manufacturing industry (sample 2009-2017). Factors of economic efficiency of investment projects of the industry are revealed. It is proved that the efficiency of investment is determined by external factors, primarily by the level of economic concentration (CR3) of the market of innovative products. The coordination of the scientific result with the industry consolidation dynamics model (A.T. Kearney) is presented.

show abstract

Kinetics of Structure Formation in the Heating of Cold-Rolled Automotive Steel Sheet

Cited by 5 publications

References 15 publications

Improvement of Technology of Formation of Coatings with Metal Effect by Modified Water-Dispersion Paints

Improvement of Technology of Formation of Coatings with Metal Effect by Modified Water-Dispersion Paints

The System of Informational Choice of the Kinematic Scheme for the Formation of Shells of a Complex Spatial Form

Data Management for Solving the Problem of Sequential Shaping Simulation

Contact Info

Product

Resources

About