Investigation on recrystallization and precipitation behaviors of Al-4.5Cu-1.5 Mg alloy refined by Ti-supported TiC nanoparticles

Bo, Zhao; Cai, Qizhou; Cheng, Jingfan; Yang, Shaogui; Chen, Fei

doi:10.1016/j.jallcom.2019.05.323

Cited by 29 publications

(1 citation statement)

References 45 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…A research was performed on the hardening and recrystallization of Al-4.5Cu-1.5Mg precipitation. The alloy was strengthened by TiC nanoparticles [13]. It is noted that 0.2 wt-% of TiC / Ti refines the average grain size by reducing the grain size to 76 µm.…”

Section: Introductionmentioning

confidence: 99%

Impact of Heat Treatment Analysis on the Wear Behaviour of Al-14.2Si-0.3Mg-TiC Composite using Response Surface Methodology

Kumar¹,

Shankar²,

Balachandran³

et al. 2021

Tribol. Ind.

View full text Add to dashboard Cite

Al-14.2Si-0.3Mg Alloy reinforced with hard phased TiC coarse particulates (10 wt-%) was contrived using the liquid metallurgy route. The so fabricated aluminium metal matrix composites was made to undergo solutionising at 525 0 C for 12 hours in a heat treatment furnace and was subsequently water quenched to room temperature. The developed composite was then kept for age hardening at varying temperatures and time for enhanced tribological properties. A pin on disc Tribometer (ASTM-G99) was utilised to study the wear properties of the fabricated composite. Aging temperature ( 0 C), applied load (N) and Aging time (hours) were chosen as the process parameters for analysing the material's resistance to wear. Using response surface methodology the influence of reinforcement in the wear properties of the composite was studied. The design of the regression equation was prepared and the impact of each experimental parameter was scrutinized. Results depict that with an increase in the aging temperature, aging time and load, there observed a variation in the materials wear properties. The worn-out surface of the metal matrix composite was then investigated with the help of the Scanning Electron Microscope (SEM).

show abstract

Section: Introductionmentioning

confidence: 99%

Impact of Heat Treatment Analysis on the Wear Behaviour of Al-14.2Si-0.3Mg-TiC Composite using Response Surface Methodology

Kumar¹,

Shankar²,

Balachandran³

et al. 2021

Tribol. Ind.

View full text Add to dashboard Cite

show abstract

Effect of CeO2 on Al–Ti–C and matrix conversion between TiC and α-Al orientation relationship

Liu

Wang

et al. 2022

J Mater Sci

View full text Add to dashboard Cite

Enhancing the Thermal Conductivity of Laser Powder Bed Fusion AlSi20 by Introducing a Novel TiC–Ti Coated Diamond Powder

Cui,

Zhang,

Yang

et al. 2024

Metall Mater Trans A

View full text Add to dashboard Cite

Investigation on recrystallization and precipitation behaviors of Al-4.5Cu-1.5 Mg alloy refined by Ti-supported TiC nanoparticles

Cited by 29 publications

References 45 publications

Impact of Heat Treatment Analysis on the Wear Behaviour of Al-14.2Si-0.3Mg-TiC Composite using Response Surface Methodology

Impact of Heat Treatment Analysis on the Wear Behaviour of Al-14.2Si-0.3Mg-TiC Composite using Response Surface Methodology

Effect of CeO2 on Al–Ti–C and matrix conversion between TiC and α-Al orientation relationship

Enhancing the Thermal Conductivity of Laser Powder Bed Fusion AlSi20 by Introducing a Novel TiC–Ti Coated Diamond Powder

Contact Info

Product

Resources

About

Investigation on recrystallization and precipitation behaviors of Al-4.5Cu-1.5 Mg alloy refined by Ti-supported TiC nanoparticles

Cited by 29 publications

References 45 publications

Impact of Heat Treatment Analysis on the Wear Behaviour of Al-14.2Si-0.3Mg-TiC Composite using Response Surface Methodology

Impact of Heat Treatment Analysis on the Wear Behaviour of Al-14.2Si-0.3Mg-TiC Composite using Response Surface Methodology

Effect of CeO2 on Al–Ti–C and matrix conversion between TiC and α-Al orientation relationship

Enhancing the Thermal Conductivity of Laser Powder Bed Fusion AlSi20 by Introducing a Novel TiC–Ti Coated Diamond Powder

Contact Info

Product

Resources

About

Investigation on recrystallization and precipitation behaviors of Al-4.5Cu-1.5 Mg alloy refined by Ti-supported TiC nanoparticles