Investigation on mechanical characterization of Al/Mos2/WC hybrid composite

Hemadri, Kadapa; Daniel, S. Ajith Arul; Kukanur, Vijayendra; Vijayananth, S.; Kumar, Rajendra

doi:10.1016/j.matpr.2022.08.014

Cited by 5 publications

(2 citation statements)

References 22 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…At 400 rpm of sliding speed, the COF values decreases. is is due to the distance travelled between the pin and the disc ratio is very low so at that level the friction between the pin and the disc decreases [21]. e results shows that the optimum parameters to attain maximum coefficient of friction is 3% of graphite and 15% of TiC, 400 rpm of sliding distance, 10 N of applied load, and 0.5 m/sec of sliding velocity.…”

Section: Resultsmentioning

confidence: 90%

Mechanical and Wear Studies on AA7075/Nano TiC/Graphite Hybrid Composites for Tribological Applications

Scaria

Pugazhenthi

Daniel

et al. 2022

Advances in Materials Science and Engineering

View full text Add to dashboard Cite

The current paper aims to study wear behaviour of AA7075 reinforced with different weight percentage of nano-TiC and graphite particles under dry sliding condition. TiC particles are taken in different weight percentages (5%, 10%, and 15%), and graphite was chosen as (3%, 4%, and 5%) along with three different levels of sliding speed, applied load, and sliding velocity. The fabrication was conducted using stir casting equipment, and the experiments were done using Taguchi’s L27 orthogonal array. The Taguchi and ANOVA results applied load and percentage of TiC are the most influencing parameters which influences wear loss and friction coefficient

show abstract

Section: Resultsmentioning

confidence: 90%

Mechanical and Wear Studies on AA7075/Nano TiC/Graphite Hybrid Composites for Tribological Applications

Scaria

Pugazhenthi

Daniel

et al. 2022

Advances in Materials Science and Engineering

View full text Add to dashboard Cite

show abstract

“…ANN is the information process that mind measures data. It comprises of countless interconnected components called neuron working in corresponding to take care of a specifc issue [16].…”

Section: Orthogonal Arraymentioning

confidence: 99%

Influence of Control Parameters during Drilling of Aluminum Reinforced with HNT Hybrid Matrix Composites

Kumar

Ruban

Daniel

et al. 2023

Advances in Materials Science and Engineering

View full text Add to dashboard Cite

The current paper aims to find the optimum control parameters such as weight percentage of HNT, weight percentage of boron nitride, drilling speed, and feed rate in drilling of aluminum hybrid metal matrix composites. The aluminum matrix material are reinforced with different weight percentage of HNT (3%, 5%, and 7%) and BN (2%, 3%, and 4%). The hybrid matrix are fabricated through the sir casting technique. The prediction of process parameter are optimized using Taguchi assisted grey relation analysis. Also the ANN model is developed to predict the output parameter. Through Taguchi S/N ratio method the effect of each control parameters are optimized. The results show that the weight percentage of HNT and feed rate are the most influencing parameters which affect the drilling of developed aluminum composites. The GRA results show that the optimum parameters are 3% of HNT, 4% of BN, 500 rpm drilling speed, and 20 mm/min in combination, which has minimum surface roughness, lower temperature, highest cutting force, and highest material removal rate.

show abstract

Understanding the machining characteristics of Al6082 hybrid metal matrix composites milled under cryogenic cooling conditions

Sivalingam,

Zhou,

Manickajothi

et al. 2023

Int J Adv Manuf Technol

View full text Add to dashboard Cite

Investigation on mechanical characterization of Al/Mos2/WC hybrid composite

Cited by 5 publications

References 22 publications

Mechanical and Wear Studies on AA7075/Nano TiC/Graphite Hybrid Composites for Tribological Applications

Mechanical and Wear Studies on AA7075/Nano TiC/Graphite Hybrid Composites for Tribological Applications

Influence of Control Parameters during Drilling of Aluminum Reinforced with HNT Hybrid Matrix Composites

Understanding the machining characteristics of Al6082 hybrid metal matrix composites milled under cryogenic cooling conditions

Contact Info

Product

Resources

About