Investigation of the mechanical properties and corrosion behaviour of hybrid L 80 Type 1 and duplex steel joints produced by magnetically impelled arc butt welding

Hassel, Thomas; Maier, Hans Jürgen; Al’khimenko, A. A.; Давыдов, А. Д.; Shaposhnikov, Nikita; Turichin, Gleb; Klimova, Olga

doi:10.1016/j.jajp.2022.100109

Cited by 4 publications

(2 citation statements)

References 25 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The E pp and E b values are listed in Table 2, along with the passivation range, which is defined as E b -E pp . The passivation range reflects the stability and durability of the passive film [59]. Therefore, a larger passivation range implies a higher resistance to pitting corrosion.…”

Section: Scc Susceptibility Testingmentioning

confidence: 99%

Investigating the Impact of Physical Vapour Deposition (PVD)-Coated Cutting Tools on Stress Corrosion Cracking Susceptibility in Turning Super Duplex Stainless Steel

Locks,

He,

DePaiva

et al. 2024

Coatings

View full text Add to dashboard Cite

This work aimed to ascertain the corresponding influences of several PVD-coated cutting tools on the susceptibility of the machined surface of super duplex stainless steel (SDSS) to stress corrosion cracking. Coatings comprised of AlCrN, AlCrN/TiSiN, and AlTiN were applied to cemented carbide cutting tools using the PVD method; these were then used to turn the outer surface of the SDSS tube section. During the cutting process, the material presents the following combination of features: (i) a tendency for strain hardening, reflected in microstructural modifications and residual stresses of the machined surface and (ii) high temperatures in the cutting region, reducing the tool life. The goal of this work was to evaluate the surface integrity (work hardening and corrosion behaviour) of the SDSS obtained after the machining process (finish turning) with cemented carbide tools coated with three different PVD coatings.

show abstract

Section: Scc Susceptibility Testingmentioning

confidence: 99%

Investigating the Impact of Physical Vapour Deposition (PVD)-Coated Cutting Tools on Stress Corrosion Cracking Susceptibility in Turning Super Duplex Stainless Steel

Locks,

He,

DePaiva

et al. 2024

Coatings

View full text Add to dashboard Cite

show abstract

“…Hassel Thomas et al [72] investigated the feasibility of the MIAB-welding technique for joining the L80 casing material and corrosion-resistant duplex steel to fabricate geothermal borehole liners and, finally, they achieved dissimilar joints with good mechanical and corrosion-resistant properties. The metallurgical challenges were overcome by Ramesh, S et al [56] who analysed, using SEM and radiography testing, the structure modification in the welded samples of SAE 213 T11 and T91 dissimilar boiler-graded steel tubes.…”

Section: Automotive Industrymentioning

confidence: 99%

Critical Review on Magnetically Impelled Arc Butt Welding: Challenges, Perspectives and Industrial Applications

Chaturvedi,

Vendan Subbiah,

Simion

et al. 2023

Materials

View full text Add to dashboard Cite

Magnetically Impelled Arc Butt (MIAB) welding is a cutting-edge joining method that replaces the conventional welding procedures such as resistance, friction, flash and butt welding. It is a solid-state process that uses a rotating arc to heat up the butt ends of tubes, being followed by a forging process that completes the joining of the workpieces The magnetic flux density and the current interact to develop the Lorentz force that impels the arc along the faying surfaces. This process is found to produce high tensile strength and defect-free welds in ferrous materials and for this reason, it is predominantly employed in automobile applications for joining metallic tubes. Also, this joining procedure can be applied in the fabrication of boilers, heat exchangers, furnace piping in petrochemical industry and other safety-critical high-pressure machinery parts. The MIAB method has several advantages such as a shorter welding cycle, lower input energy requirement and lower loss of material. Compared to other solid-state welding processes, the MIAB welding has an important advantage in terms of cost-efficient welds with better control and reliability. Moreover, there are researchers who have investigated the joining of non-ferrous dissimilar materials using this welding procedure. The studies have been focused on process parametric analysis that involves optimizing and forecasting the magnetic field and thermal profile distribution. This review article provides competitive insights into various design features, computational methods, tests and material characterization, technical issues and workarounds, as well as automation aspects related to the MIAB-welding process. This work will prove to be a quick reference for researchers, useful to identify the research gaps and conflicting ideas that can be further explored for advancements in joining the similar and dissimilar materials.

show abstract

Magnetically impelled arc butt welding (MIAB): a comprehensive review on welding parameters, microstructure, and joint performance

Santhosh Kumar,

Ramesh Kumar

2023

Weld World

View full text Add to dashboard Cite

Investigation of the mechanical properties and corrosion behaviour of hybrid L 80 Type 1 and duplex steel joints produced by magnetically impelled arc butt welding

Cited by 4 publications

References 25 publications

Investigating the Impact of Physical Vapour Deposition (PVD)-Coated Cutting Tools on Stress Corrosion Cracking Susceptibility in Turning Super Duplex Stainless Steel

Investigating the Impact of Physical Vapour Deposition (PVD)-Coated Cutting Tools on Stress Corrosion Cracking Susceptibility in Turning Super Duplex Stainless Steel

Critical Review on Magnetically Impelled Arc Butt Welding: Challenges, Perspectives and Industrial Applications

Magnetically impelled arc butt welding (MIAB): a comprehensive review on welding parameters, microstructure, and joint performance

Contact Info

Product

Resources

About