Investigation of load bearing performances of pin connected carbon/polyphenylene sulphide composites under static loading conditions

Yýlmaz, Taner; Sýnmazçelik, Tamer

doi:10.1016/j.matdes.2005.08.015

Cited by 42 publications

(28 citation statements)

References 17 publications

(18 reference statements)

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The volume fraction of carbon fibers is 50%, and the mass fraction is 57%. The carbon fiber fabric, reference T300 3K 5HS, was supplied by Soficar (Abidos, France 7 , each ply consists of fibers oriented at +45…”

Section: Materials and Specimensmentioning

confidence: 99%

“…The laminate stacking sequence for compression tests is [90] 7 what is approximately equivalent to a [0] 7 layup because the reinforcement fabric is balanced in the weft and warp directions. The compressive tests require the use of a specific fixture preventing specimen's buckling (see Fig.…”

Section: Compressive Testmentioning

confidence: 99%

“…10). The laminate's stacking sequence is [90] 7 . Classical beam theory gives the maximum tensile σ u (or compressive) and shear τ u stresses due to flexural loading: σ u = 3F m L 2wt 2 and τ u = 3F m /4wt where F m corresponds to the maximum load applied to the specimen during the test, w and t being, respectively, the width and thickness of the specimen.…”

Section: Flexural Testmentioning

confidence: 99%

“…• C. 7 There is no study currently available in the literature that investigates the joints' strength at elevated temperature for carbon fabric reinforced PPS. Thus, very few works highlight the behavior of carbon fabric PPS laminates 8,9 and a few authors investigated the influence of high temperatures on the behavior of UD-reinforced PPS matrix.…”

mentioning

confidence: 99%

See 3 more Smart Citations

Carbon fiber fabric reinforced PPS laminates: Influence of temperature on mechanical properties and behavior

Vieille¹,

Aucher²,

Taleb³

2011

Adv Polym Technol

View full text Add to dashboard Cite

This paper is aimed at investigating the influence of temperature on mechanical properties and behavior of carbon fiber fabric reinforced polyphenylenesulfide (PPS) laminates subjected to different loadings: tensile, open hole tensile, in-plane shear, compressive, flexural, interlaminar shear, single-bolt double lap joint, and single-bolt single lap joint tests. The resulting experimental database is of the utmost importance for generating design allowables for structures integrating such thermoplastic-based composites. Depending on the test and the laminate's staking sequence, a temperature increase higher than the glass transition temperature (T g = 98• C) of fiber fabric reinforced PPS laminates softens the matrix behavior and significantly degrades the quality of the adhesion at the fiber/matrix interface, resulting in reduced mechanical properties (in-plane shear, compressive, flexural and interlaminar shear). However, it does not seem to be detrimental for the tensile and the double lap joint's properties in quasi-isotropic laminates. In angle-ply laminates, the ductile behavior of the PPS matrix is exacerbated at high temperature resulting in

show abstract

Section: Materials and Specimensmentioning

confidence: 99%

Section: Compressive Testmentioning

confidence: 99%

Section: Flexural Testmentioning

confidence: 99%

mentioning

confidence: 99%

See 2 more Smart Citations

Carbon fiber fabric reinforced PPS laminates: Influence of temperature on mechanical properties and behavior

Vieille¹,

Aucher²,

Taleb³

2011

Adv Polym Technol

View full text Add to dashboard Cite

show abstract

“…The high processing temperature about 280-300 o C is one of significant feature of PPS resin [16][17][18][19][20]. Hence, the surfactants which are used to modify the clays must survive the fabrication process, in other words, the temperature or the blending time under shear must not lead to surfactants degradation.…”

Section: Introductionmentioning

confidence: 99%

Effect of benzimidazolium salt on dispersion and properties of polyphenylene sulfide/organic clay nanocomposites via melt intercalation

2015

View full text Add to dashboard Cite

Nanocomposites of polyphenylene sulfide (PPS) were prepared with a benzimidazolium surfactant used as organic modification for the montmorillonite (MMT) by melt blending. The benzimidazolium-modifided MMT (Bz-MMT) exhibited a large interlayer spacing of 3.26 nm and showed a high thermal stability compared to the commonly used clay modified by alkyl ammonium salts (DK-1N). The morphology of the polyphenylene sulfide (PPS)/Bz-MMT nanocomposites were evaluated by X-ray diffraction (XRD) and transmission electron microscope (TEM). The results showed good overall dispersion of the MMT in PPS matrix. Differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were used to evaluate the thermal properties of polymer/clay nanocomposites. The results of DSC showed the addition of MMT resulted in heterogeneous nucleation crystallization of PPS. The results of TGA showed the thermal stability of the polymer/ clay nanocomposits was enhanced. The rheological properties of nanocomposites were also evaluated by a Anton Paar rheometer. The results indicated that the addition of Bz-MMT nanoplatelets affected the linear viscoelastic behavior of the PPS matrix by increasing the viscosity.

show abstract

Introduction to special issue on developmental and reproductive toxicology in China

Daston¹

2010

Birth Defects Research Pt B

View full text Add to dashboard Cite

This paper is aimed at investigating the influence of temperature on mechanical properties and behavior of carbon fiber fabric reinforced polyphenylenesulfide (PPS) laminates subjected to different loadings: tensile, open hole tensile, in‐plane shear, compressive, flexural, interlaminar shear, single‐bolt double lap joint, and single‐bolt single lap joint tests. The resulting experimental database is of the utmost importance for generating design allowables for structures integrating such thermoplastic‐based composites. Depending on the test and the laminate's staking sequence, a temperature increase higher than the glass transition temperature (Tg = 98°C of fiber fabric reinforced PPS laminates softens the matrix behavior and significantly degrades the quality of the adhesion at the fiber/matrix interface, resulting in reduced mechanical properties (in‐plane shear, compressive, flexural and interlaminar shear). However, it does not seem to be detrimental for the tensile and the double lap joint's properties in quasi‐isotropic laminates. In angle‐ply laminates, the ductile behavior of the PPS matrix is exacerbated at high temperature resulting in larger plastic deformations and a lesser hole sensitivity of this material. © 2011 Wiley Periodicals, Inc. Adv Polym Techn 30: 80–95, 2011; View this article online at wileyonlinelibrary.com. DOI 10.1002/adv.20239

show abstract

Investigation of load bearing performances of pin connected carbon/polyphenylene sulphide composites under static loading conditions

Cited by 42 publications

References 17 publications

Carbon fiber fabric reinforced PPS laminates: Influence of temperature on mechanical properties and behavior

Carbon fiber fabric reinforced PPS laminates: Influence of temperature on mechanical properties and behavior

Effect of benzimidazolium salt on dispersion and properties of polyphenylene sulfide/organic clay nanocomposites via melt intercalation

Introduction to special issue on developmental and reproductive toxicology in China

Contact Info

Product

Resources

About