Investigation Corrosion and Wear Behavior of Nickel-Nano Silicon Carbide on Stainless Steel 316L

Dawood, Nawal Mohammed; Radhi, Nabaa S.; Al-Khafaji, Zainab S.

doi:10.4028/www.scientific.net/msf.1002.33

Cited by 18 publications

(11 citation statements)

References 23 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Martensite is well-known as a ductile and softer steel crystalline structure when compared with Austenite. Whereas, Austenite is considered stronger and hardness [16,17]. Therefore, it is noticeable that the availability of phase Martensite is more than the Austenite phase from those samples which consist of steel.…”

Section: Resultsmentioning

confidence: 99%

“…Therefore, the application of this concept on metal matrix composites (MMCs) can be a reason for the development and the designing of different components, such as reinforcing the materials in places which required more modulus, strength and wear resistance. The FGMs refer to the grading in the material characteristics, and this can play a significant role in the industrial uses, especially the use of MMCs [16].…”

Section: Introductionmentioning

confidence: 99%

See 1 more Smart Citation

Optimization of Nickel Content on Some Properties of (Niti) Shape Memory Alloy

Bouaissi

Radhi

Morad

et al. 2020

Kbes

View full text Add to dashboard Cite

Shape Memory Alloys (SMAs) are one of the most hopeful smart materials, especially, Nickel–Titanium (NiTi or Nitinol). These alloys are great and desirable due to their excellent reliability and behavior among all the commercially available alloys. In addition, strain recovery, (Ni–Ti) is granulated for a wide variety of medical uses because of its favorite properties such as fatigue behavior, corrosion resistance and biocompatibility. This paper explores the creation and the characterization of functionally graded (NiTi) materials. This work demonstrations the impact of Nickel contains changes on the characteristics of NiTi shape memory alloy, in order to obtain the suitable addition of Nickel contain, which gives the optimal balance between hardness, start and finish martensitic point, shape recovery and shape effect of alloys properties. These materials are prepared to obtain suddenly or gradually microstructure or composition differences inside the structure of one piece of material, the specimens made by powder metallurgy process and the influence of every layer of composite by; micro-hardness, transformation temperature DSC and shape effect. The hardness value and shape recovery decrease with increase nickel content. superior shape memory effect (SME) and shape recovery (SR) properties (i.e., 8.747, 10.270 for SMA-FGM1 SMA-FGM2 respectively, and SR is 1.735, 2.977 for SMA-FGM1 SMA-FGM2) respectively.

show abstract

Section: Resultsmentioning

confidence: 99%

Section: Introductionmentioning

confidence: 99%

Optimization of Nickel Content on Some Properties of (Niti) Shape Memory Alloy

Bouaissi

Radhi

Morad

et al. 2020

Kbes

View full text Add to dashboard Cite

show abstract

“…The research [6] signifies an attempt to apply composite coating by co-deposition coating and assessing, enhancement the Nickel coatings features, by adding the particles of silicon-carbide to solution of electrodeposited. Stainless steel specimens have been subject to electroplating coating utilizing Nickel and Nano silicon carbide particles (70-100 nm) with various amounts (16, 24, 32 and 40) g/L.…”

Section: Review Of the Latest Researchmentioning

confidence: 99%

Wear Resistance Research and Its 2-factor Modeling of Nanoscaled Silicon Carbide Detonation Coatings

Dovgal

Pryimak

Varijukhno

2023

View full text Add to dashboard Cite

This research is related to the spheres of wearproof coating testing. The SiC coating has been deposited on the medium carbon steel using detonation deposition using the magnet coil flux of back direction. It has been established that only nanoscaled particles are deposited on the surface which had been accumulated in aggregates of different shape. The structure of the obtained coating has been thoroughly researched on the electronic microscope in previous publication. The obtained coating has been developed for testing on the friction bench modeling the friction process that is taking place in the couple of main and rod journals of internal combustion engines. The coating has also the corrosion protection properties. The nanoscaled coating on mild carbon steel had been tested under specified conditions and their friction surfaces had been researched on electronic microscope with the view of determination of wear mechanism. The two-factor modeling of the wear rate and friction factor has been done and three-dimensional diagrams have been plotted and analyzed.

show abstract

“…The turbine steam blades transform the linear motion of high pressure and high temp steam flowing down a pressure difference into a rotational motion of the turbine shaft in power plants. Power stations will shut down if turbine blades fail [1][2][3]. These substances may be used in corrosive and/or high-temp settings including rotors, turbine blades, and steam pipes [4].…”

Section: Introductionmentioning

confidence: 99%

Influence Of Laser Cladding on Behavior of Fatigue and Fatigue Corrosion

Abdulwahab

Ajeel

Jafar

2022

IOP Conf. Ser.: Earth Environ. Sci.

View full text Add to dashboard Cite

Nickle based super alloys such as Inconel 600 are being extensively used to manufacture turbine blades for jet engines since their superior mechanical characteristics at higher working temps. The chemical composition of steam turbine blades show that is steel 52 it has a wide range of Energy, Tanks, Rail, Yellow Goods, Engineering, Bridges, Construction, applications. Laser cladding seems to be a surfacing method that uses lasers to improve the characteristics of a component’s surface and/or renew it. Laser cladding involves absorption of laser light that melts a small area of the substrates against which the substance was being introduced and fuses the coating substance to the substrates, resulting in the formation of a new layer. This research aims to investigate the fatigue and fatigue corrosion behavior of these turbine blades before and after exposure to laser cladding. The cladding process applied with this parameter Pulse energy = 11 joules, Pulse width = 6 Ms., Pulse frequency = 12 Hz, Laser Average Power = 132 W, Laser peak power = 1.83 KW. The results show, after cladding process the microstructure of the specimen is smooth and increase the cyclic of fatigue comparison with specimen without laser cladding process. So, the fatigue resistance is increased.

show abstract

Investigation Corrosion and Wear Behavior of Nickel-Nano Silicon Carbide on Stainless Steel 316L

Cited by 18 publications

References 23 publications

Optimization of Nickel Content on Some Properties of (Niti) Shape Memory Alloy

Optimization of Nickel Content on Some Properties of (Niti) Shape Memory Alloy

Wear Resistance Research and Its 2-factor Modeling of Nanoscaled Silicon Carbide Detonation Coatings

Influence Of Laser Cladding on Behavior of Fatigue and Fatigue Corrosion

Contact Info

Product

Resources

About