Internet of Things-Based Steam Pump Motor Protection Due to Voltage Unbalance

Saputra, Bagas Aji; Hidayat, Edy Prasetyo; Arfianto, Afif Zuhri

doi:10.18196/jrc.1214

Cited by 6 publications

(7 citation statements)

References 23 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The system was designed to maintain a stable indoor temperature with minimal energy consumption. The temperature, humidity, and energy consumption were monitored before and after the implementation of the PID control system [64] [65].…”

Section: Methodsmentioning

confidence: 99%

Integrated Room Monitoring and Air Conditioning Efficiency Optimization Using ESP-12E Based Sensors and PID Control Automation: A Comprehensive Approach

Desnanjaya,

Pradhana,

Putra

et al. 2023

Journal of Robotics and Control

View full text Add to dashboard Cite

This study addresses the critical need for efficient room monitoring and air conditioning systems, particularly in educational settings like the STMIK STIKOM Indonesia campus. The paper introduces a novel approach that combines ESP-12E based sensors with Proportional-Integral-Derivative (PID) control automation to optimize air conditioning efficiency. Utilizing an ESP-12E microcontroller, the study designed and implemented a room monitoring tool equipped with DHT22 and BH1750 sensors for accurate measurement of temperature, humidity, and light intensity. We also explores the integration of a PID control system into an existing air conditioning (AC) unit. The PID controller was fine-tuned to maintain a stable indoor temperature of 25oCelsius, even when subjected to external heat loads, such as ten LED lamps. The effectiveness of this system was quantified through real-time monitoring of temperature, humidity, and energy consumption, both pre- and post-implementation. Results indicated a rapid and stable response from the PID controller, achieving an amplitude of 1 within 0.08 seconds, thereby confirming its successful tuning and adaptability. We found that this study has broader implications for enhancing energy efficiency and creating conducive learning environments. However, it is worth noting that the research was conducted under specific conditions, and further studies could explore its applicability in different settings.

show abstract

Section: Methodsmentioning

confidence: 99%

Integrated Room Monitoring and Air Conditioning Efficiency Optimization Using ESP-12E Based Sensors and PID Control Automation: A Comprehensive Approach

Desnanjaya,

Pradhana,

Putra

et al. 2023

Journal of Robotics and Control

View full text Add to dashboard Cite

show abstract

“…The sensors contained in the digester tank worked to monitor the biogas' concentration and the temperature produced by the biogas reactor, while the sensor mounted on the storage tank was to see any leakage or gas when the gas flowed from the digester tank. Figure 1 displays the P&ID [20]- [23] flow diagram of the biogas reactor monitoring process.…”

Section: Research Methods 21 System Workflowmentioning

confidence: 99%

Design of gas concentration measurement and monitoring system for biogas power plant

Iswanto

Ma’arif

Kebenaran

et al. 2021

IJEECS

View full text Add to dashboard Cite

Biogas is a gas obtained from the breakdown of organic matter (such as animal waste, human waste, and plants) by methanogenic bacteria in an oxygen-free (anaerobic) state. The biogas produced mainly consists of 50-70% methane, 30-40% carbon dioxide, and other gases in small amounts. The gas produced has a different composition depending on the type of animal that produces it. It is challenging to obtain biogas concentration data because the monitoring equipment is currently minimal. Therefore, this research discusses how to make a monitoring system for biogas reactors. Sensors are installed in the digester tank and storage tank. The installed sensors are the MQ-4 sensor to detect methane gas (CH4), MG-811 sensor to detect carbon dioxide (CO2) gas, MQ-136 sensor to detect sulfide acid gas (H2S), and Thermocouple Type-K to detect temperature. The sensor will send a signal to the control unit in Arduino Mega 2560, then processed and displayed on the liquid crystal display (LCD). The sensor calculation results' accuracy is not much different from the reference based on the sensor readings. The sensor deviation standard is below 5.0, indicating that the sensor is in precision. The sensor's linearity of MQ-4 is 0.7%, the MG-811 is 0.17%, the MQ-136 is 0.29%, and the Type-K Thermocouple is 1.19%. The installed sensor can be used to monitor gas concentration and temperature in a biogas reactor.

show abstract

“…This work uses the ATmega (8-bit) that is installed in the Arduino Mega 2560 board with the addition of Ethernet Shield 2, the board contains a successive approximation register/analog to digital converter (SAR ADC) (10-bit) with a 10 khz sampling rate [2]- [4], [24]. The Ethernet Shield 2 board is added to the system to provide a wireless data link between the two parts of the network [9], [25]. The microcontroller system used a voltage sensor based on a voltage divider operation instead of the widely used ZMPT101B voltage sensor because the latter yields an inappropriate response for quasi-square voltage as shown in Figure 2 [26]- [28].…”

Section: Microcontroller Systemmentioning

confidence: 99%

A novel Ethernet based processing system for remote source harmonic detection

2023

View full text Add to dashboard Cite

This work is carried out to objectively establish a new method to detect harmonics and measure the total harmonic distortion (THD) in a remote source, such as a high voltage transformer. The proposed approach utilized embedded design techniques to construct an embedded processor system with Ethernet intellectual property core to acquire data from a remote harmonics source. The designed system has several notable merits, namely, it is portable that can be applied in the work field, and it avoids workers from being subject to a hazard high voltage shock as well as its simplicity and high accuracy. The harmonics detection and analysis are achieved by inserting a microcontroller system near the high voltage transformer to acquire the necessary data and transmit it to a remote embedded processor system that is used to detect and analyze the harmonics. The microcontroller and the processor systems are connected by a wide-area network (WAN) through Ethernet and transmission control protocol/internet protocol (TCP/IP) protocols. The processor system is accommodated to perform 128 points fast Fourier transform for harmonics detection. Matlab simulations are used to validate the results. It is found that the results match very accurately the simulation results with an error of less than 0.02%.

show abstract

Internet of Things-Based Steam Pump Motor Protection Due to Voltage Unbalance

Cited by 6 publications

References 23 publications

Integrated Room Monitoring and Air Conditioning Efficiency Optimization Using ESP-12E Based Sensors and PID Control Automation: A Comprehensive Approach

Integrated Room Monitoring and Air Conditioning Efficiency Optimization Using ESP-12E Based Sensors and PID Control Automation: A Comprehensive Approach

Design of gas concentration measurement and monitoring system for biogas power plant

A novel Ethernet based processing system for remote source harmonic detection

Contact Info

Product

Resources

About