Interfacial characteristics of composites fabricated by laminated object manufacturing

Klosterman, Donald A.; Chartoff, Richard P.; Graves, George; Osborne, Nora; Priore, Brian

doi:10.1016/s1359-835x(98)00088-8

Cited by 124 publications

(71 citation statements)

References 1 publication

Supporting

Mentioning

Contrasting

Unclassified

Order By: Relevance

“…Originally known as layered laminated manufacturing, later on commercialized under the trade name LOM by Helysis (now Cubic Technologies; Torrance, CA) or CerLAM and MetLAM by Javelin 3D (Draper, UT), this AM process deals with the 3D building of parts by the lamination of paper, tapes, or similar shapes at low‐medium temperature and pressure. LOM has been considered as an alternative for the lamination of green ceramic tapes into 3D dense or semidense parts …”

Section: Am Technologies For Ceramicsmentioning

confidence: 99%

Additive Manufacturing of Ceramics: Issues, Potentialities, and Opportunities

et al. 2015

View full text Add to dashboard Cite

Additive manufacturing (AM) is a technology which has the potential not only to change the way of conventional industrial manufacturing processes, adding material instead of subtracting, but also to create entirely new production and business strategies. Since about three decades, AM technologies have been used to fabricate prototypes or models mostly from polymeric or metallic materials. Recently, products have been introduced into the market that cannot be produced in another way than additively. Ceramic materials are, however, not easy to process by AM technologies, as their processing requirements (in terms of feedstock and/or sintering) are very challenging. On the other hand, it can be expected that AM technologies, once successful, will have an extraordinary impact on the industrial production of ceramic components and, moreover, will open for ceramics new uses and new markets.

show abstract

Section: Am Technologies For Ceramicsmentioning

confidence: 99%

Additive Manufacturing of Ceramics: Issues, Potentialities, and Opportunities

et al. 2015

View full text Add to dashboard Cite

show abstract

“…Curved body armor parts were produced from the SiC tapes, but large overlap areas led to complications while removing waste material. [275] A curved layered LOM process was developed to minimize overlap areas. [276,277] The tapes were placed on a mandrel with the desired curvature and laminated by a flexible thermoforming mechanism, Figure 11.…”

Section: Laminated Object Manufacturing (Lom)mentioning

confidence: 99%

Additive Manufacturing of Ceramic‐Based Materials

et al. 2014

View full text Add to dashboard Cite

This paper offers a review of present achievements in the field of processing of ceramic-based materials with complex geometry using the main additive manufacturing (AM) technologies. In AM, the geometrical design of a desired ceramic-based component is combined with the materials design. In this way, the fabrication times and the product costs of ceramic-based parts with required properties can be substantially reduced. However, dimensional accuracy and surface finish still remain crucial features in today's AM due to the layer-by-layer formation of the parts. In spite of the fact that significant progress has been made in the development of feedstock materials, the most difficult limitations for AM technologies are the restrictions set by material selection for each AM method and aspects considering the inner architectural design of the manufactured parts. Hence, any future progress in the field of AM should be based on the improvement of the existing technologies or, alternatively, the development of new approaches with an emphasis on parts allowing the near-net formation of ceramic structures, while optimizing the design of new materials and of the part architecture.

show abstract

“…nevertheless, it is not possible to use material other than paper. In the case of old LOM machines there are some works for creating composites using this technology [9,10]. …”

Section: Laminated Object Manufacturing (Lom)mentioning

confidence: 99%

Rapid Prototyping: Technologies, Materials and Advances

Dudek¹,

Rapacz-Kmita²

2016

Archives of Metallurgy and Materials

View full text Add to dashboard Cite

In the context of product development, the term rapid prototyping (RP) is widely used to describe technologies which create physical prototypes directly from digital data. Recently, this technology has become one of the fastest-growing methods of manufacturing parts. The paper provides brief notes on the creation of composites using RP methods, such as stereolithography, selective laser sintering or melting, laminated object modelling, fused deposition modelling or three-dimensional printing. The emphasis of this work is on the methodology of composite fabrication and the variety of materials used in these technologies.

show abstract

Interfacial characteristics of composites fabricated by laminated object manufacturing

Cited by 124 publications

References 1 publication

Additive Manufacturing of Ceramics: Issues, Potentialities, and Opportunities

Additive Manufacturing of Ceramics: Issues, Potentialities, and Opportunities

Additive Manufacturing of Ceramic‐Based Materials

Rapid Prototyping: Technologies, Materials and Advances

Contact Info

Product

Resources

About