Influence of Ti–O–Si hetero-linkages in the photocatalytic degradation of Rhodamine B

Rasalingam, Shivatharsiny; Kibombo, Harrison S.; Wu, Chia-Ming; Budhi, Sridhar; Peng, Rui; Baltrušaitis, Jonas; Koodali, Ranjit T.

doi:10.1016/j.catcom.2012.11.016

Cited by 60 publications

(41 citation statements)

References 29 publications

(33 reference statements)

Supporting

Mentioning

Contrasting

Order By: Relevance

“…HO radicals were detected by fluorescence technique [35] that detects the amount of these species formed on photocatalyst surface. The radicals react with terephthalic acid (TPA) to produce highly fluorescent 2-hydroxyterephthalic acid.…”

Section: Photocatalytic Degradation Experimentsmentioning

confidence: 99%

Mesoporous CeTiSiMCM-48 as novel photocatalyst for degradation of organic compounds

Mureşeanu

Pârvulescu

Radu

et al. 2015

Journal of Alloys and Compounds

View full text Add to dashboard Cite

Section: Photocatalytic Degradation Experimentsmentioning

confidence: 99%

Mesoporous CeTiSiMCM-48 as novel photocatalyst for degradation of organic compounds

Mureşeanu

Pârvulescu

Radu

et al. 2015

Journal of Alloys and Compounds

View full text Add to dashboard Cite

“…Additionally the broad Ti 2p peak suggests the presence of titanium with lower oxidation states, and the line slightly became broad with added calcium [34], and the peak shifted with the Ca loading to high binding energy, which meaning more oxidized state. Generally the O 1s binding energies are located in the 530.9-536.2 eV regions [35]. In this study, the binding energy at 530.9 eV and 533.7 eV can be assigned to TiO 2 and SiO 2 , respectively.…”

Section: Photocatalytic Activity Test For Ca/ti X Simcm-41smentioning

confidence: 77%

“…CH 4 was not produced over pure Ca(5.0 wt.%)/SiMCM-41, but the level of production increased gradually with increasing Ti-content. On the other hand, in Ti 35 Si 65 MCM-41 sample without Ca ingredient loading, the methane generation did not significantly increase compared to the Ca loaded Ti35 Si 65 MCM-41 sample. This is an evidence that the Ca ingredient affects the photoreaction of CO 2 perhaps increasing the amount of adsorption of carbon dioxide on the calcium surfaces.…”

mentioning

confidence: 73%

“…When the light was turned on, a rapid increase in the photoreduction current was observed, and the photocurrent then turned to a steady state after a few seconds, as light off, the photocurrent dropped to nearly zero instantaneously [43]. When the light was turned on, the maximum photocurrent was obtained for the Ca(10.0 wt.%)/Ti 35 Si 65 MCM-41 film with 137 nA cm −2 , which is 9.6% higher than that achieved on Ti 35 Si 65 MCM-41 film (113 nA cm −2 ). Additionally there are no Scheme 1.…”

Section: Catalytic Efficiencies Of Co 2 Photoreduction Over Ca/ti X Smentioning

confidence: 90%

“…The lowest pore volume has the largest average pore diameter because of the increasing nonstructural porosity consisting of some irregular cavities that permeate the entire bulk and give rise to secondary porosity. X-ray photoelectron spectroscopy (XPS) analysis for two samples, Ti 35 [35]. These species are related to photocatalytic activity on Si O Ti systems, perhaps acting as adsorption sites of the reactants.…”

Section: Photocatalytic Activity Test For Ca/ti X Simcm-41smentioning

confidence: 99%

See 2 more Smart Citations

Effectively CO 2 photoreduction to CH 4 by the synergistic effects of Ca and Ti on Ca-loaded TiSiMCM-41 mesoporous photocatalytic systems

Kwak

Kim

et al. 2015

Applied Surface Science

View full text Add to dashboard Cite

Polysiloxane Cross‐Linked Mechanically Stable MXene‐Based Lithium Host for Ultrastable Lithium Metal Anodes with Ultrahigh Current Densities and Capacities

Qian

Fan

Peng

et al. 2020

Adv Funct Materials

View full text Add to dashboard Cite

The applications of lithium metal anode are limited by uncontrollable lithium dendrite growth and infinite volume changes during cycling. These fundamental issues are exacerbated at high cycling current densities and capacities. Herein, a mechanically stable and resilient lithium metal host is fabricated by covalently cross‐linking a highly‐conductive and lithiophilic MXene/silver nanowire scaffold through a silylation reaction between MXene nanosheets and polysiloxane. Compared with the control sample (an MXene scaffold assembled by weak van der Waals forces), the covalently cross‐linked MXene scaffold displays excellent mechanical strength and resilience, which is conducive to buffer the large internal stress fluctuations generated during rapid and deep lithium plating‐stripping and guaranteed that the integrated framework structure is maintained during long‐term charging‐discharging cycles. When used in a symmetric cell, the lithium composite anode based on the covalently cross‐linked MXene host affords an unprecedented cyclic lithium plating‐stripping stability of a record‐high 3000 h lifespan at an ultrahigh current density (20 mA cm−2) and areal capacity (10 mAh cm−2). When this composite anode is coupled with a LiNi0.5Co0.2Mn0.3O2 cathode, the full cell delivers an ultrahigh rate of 10 C for up to 1000 cycles, with an average capacity decay of 0.043% per cycle and a stable Coulombic efficiency of 98.7%.

show abstract

Influence of Ti–O–Si hetero-linkages in the photocatalytic degradation of Rhodamine B

Cited by 60 publications

References 29 publications

Mesoporous CeTiSiMCM-48 as novel photocatalyst for degradation of organic compounds

Mesoporous CeTiSiMCM-48 as novel photocatalyst for degradation of organic compounds

Effectively CO 2 photoreduction to CH 4 by the synergistic effects of Ca and Ti on Ca-loaded TiSiMCM-41 mesoporous photocatalytic systems

Polysiloxane Cross‐Linked Mechanically Stable MXene‐Based Lithium Host for Ultrastable Lithium Metal Anodes with Ultrahigh Current Densities and Capacities

Contact Info

Product

Resources

About