In situ tribology of nanocomposite Ti–Si–C–H coatings prepared by PE-CVD

Strauss, Holger W.; Chromik, Richard R.; Hassani, Salim; Klemberg-Sapieha, Jolanta E.

doi:10.1016/j.wear.2011.08.001

Cited by 53 publications

(22 citation statements)

References 45 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…As expected, the free carbon phase significantly increased for the coatings of series-2. The existence of a free carbon phase was frequently reported for overstoichiometric carbide or carbonitride coatings [34][35][36], promoting the formation of nanostructures and determining the superior friction behavior of such coatings.…”

Section: Chemical Bonds and Elemental Compositionsmentioning

confidence: 99%

Effects of substrate temperature and carbon content on the structure and properties of (CrCuNbTiY)C multicomponent coatings

Braic

Parau

Pană

et al. 2014

Surface and Coatings Technology

View full text Add to dashboard Cite

Section: Chemical Bonds and Elemental Compositionsmentioning

confidence: 99%

Effects of substrate temperature and carbon content on the structure and properties of (CrCuNbTiY)C multicomponent coatings

Braic

Parau

Pană

et al. 2014

Surface and Coatings Technology

View full text Add to dashboard Cite

“…After the values of hardness and elastic modulus obtained by nanoindentation for each austenitic crystallographic orientation the wear resistance has been directly estimated by using the following expression [64,65,66]:…”

Section: E Wear Resistance Estimationmentioning

confidence: 99%

Dependence of nanoindentation hardness with crystallographic orientation of austenite grains in metastable stainless steels

Roa

Fargas

Mateo

et al. 2015

Materials Science and Engineering: A

View full text Add to dashboard Cite

“…Wear testing was performed using a custom-built linear reciprocating tribometer (ball-on-flat configuration) [17]. All wear tests were conducted in dry sliding conditions (unlubricated) in ambient air at room temperature (*21°C) and room humidity (37-42% RH).…”

Section: Tribology Testsmentioning

confidence: 99%

Microstructure and Tribology of Spark Plasma Sintered Fe–Cr–B Metamorphic Alloy Powder

et al. 2011

Self Cite

View full text Add to dashboard Cite

The spark plasma sintering (SPS) process was used to fabricate a bulk Fe-Cr-B alloy (known as Armacor M) from gas-atomized powders. The purpose of this work is to study the microstructure, hardness and tribology of this sintered bulk alloy. Post microstructure and mechanical characterizations were performed to investigate the effects of wear on the microstructure and mechanical properties. Microstructural analysis using X-ray diffraction (XRD), scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS) showed that SPS successfully produced a fully dense bulk material containing 67 vol.% Cr 1.65 Fe 0.35 B 0.96 particles dispersed in 33 vol.% solid solution matrix consisting of Fe, Cr and Si. Using nanoindentation, the hardness of the Cr 1.65 Fe 0.35 B 0.96 particles and the matrix was found to be 24 and 6 GPa, respectively. From microindentation, the bulk hardness of the sintered alloy was 9.7 GPa (991 HV). Dry sliding wear testing under mild conditions (i.e., initial Hertzian mean contact pressure of 280 MPa) was conducted against a stainless steel pin. The steady state coefficient of friction against Armacor M was about 0.82. The wear of Armacor M proceeded primarily by adhesive and mild oxidative wear. The wear volume for Armacor M was 80% less than that of carbon steel and its wear rate was 5.53 9 10 -6 mm 3 N -1 m -1 .

show abstract

In situ tribology of nanocomposite Ti–Si–C–H coatings prepared by PE-CVD

Cited by 53 publications

References 45 publications

Effects of substrate temperature and carbon content on the structure and properties of (CrCuNbTiY)C multicomponent coatings

Effects of substrate temperature and carbon content on the structure and properties of (CrCuNbTiY)C multicomponent coatings

Dependence of nanoindentation hardness with crystallographic orientation of austenite grains in metastable stainless steels

Microstructure and Tribology of Spark Plasma Sintered Fe–Cr–B Metamorphic Alloy Powder

Contact Info

Product

Resources

About