Hydrophilic Modified Clay Nanocomposites: Effect of Clay on Thermal and Vibrational Properties

Kishore, A. Nanda; Venkatesh, D.B.; Kumar, M. Ashok; Ramesh, A.; Murthy, K. Nikil; Karthikeyan, N.

doi:10.18052/www.scipress.com/ilcpa.27.73

Cited by 3 publications

(3 citation statements)

References 21 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The grafted fiber molecules played a role of tie molecules between the reinforcing particles and epoxy matrix. Flexural strength was increased with increase in CF content up to 30% (by mass), whereas on other hand, decreases when SD content increases, the reason is increase in SD content obviously make mixture makes difficult to flow as mentioned earlier same was observed by the authors [23,26]. Same results were observed even at for modulus.…”

Section: Resultssupporting

confidence: 72%

Effects of Performance on Mechanical Properties of Sawdust/Carbon Fibre Reinforced Polymer Matrix Hybrid Composites

Kumar

Chowdary

Balaji

et al. 2015

ILCPA

View full text Add to dashboard Cite

Short carbon fibre (CF) and sawdust (SD) were dispersed in to the epoxy (EP) matrix in order to manufacture polymer hybrid composites using compression moulding technique. The mechanical properties of flexural properties of hybrid, compression moulded, chopped CF/SD/epoxy composites have been investigated taking into account the effect of hybridization by these two fillers. Hybridization with small amounts of SD makes these CF composites more suitable for technical applications. The simultaneous compounding of epoxy with two fillers was done to obtain a hybrid composite. This system is expected to have considerable mechanical properties, good surface finish and low cost. It has been found that the tensile properties of filled epoxy were higher than unfilled epoxy. By incorporating up to 30% (by mass) Carbon fiber (CF) and 10% sawdust (SD) namely S3 sample flexural strength was increased by 12.5%. Thus it is shown that the durability of CF/SD filled epoxy composites can be enhanced by hybridization with small amount of CF. The hybrid effects of the flexural strength and modulus were studied by the rule of hybrid mixture.

show abstract

Section: Resultssupporting

confidence: 72%

Effects of Performance on Mechanical Properties of Sawdust/Carbon Fibre Reinforced Polymer Matrix Hybrid Composites

Kumar

Chowdary

Balaji

et al. 2015

ILCPA

View full text Add to dashboard Cite

show abstract

Section: International Letters Of Chemistry Physics and Astronomy Vosupporting

confidence: 73%

Effects of Performance on Mechanical Properties of Sawdust/Carbon Fibre Reinforced Polymer Matrix Hybrid Composites

Kumar

Chowdary

Balaji

et al. 2015

ILCPA

View full text Add to dashboard Cite

ABSTRACT. Short carbon fibre (CF) and sawdust (SD) were dispersed in to the epoxy (EP) matrix in order to manufacture polymer hybrid composites using compression moulding technique. The mechanical properties of flexural properties of hybrid, compression moulded, chopped CF/SD/epoxy composites have been investigated taking into account the effect of hybridization by these two fillers. Hybridization with small amounts of SD makes these CF composites more suitable for technical applications. The simultaneous compounding of epoxy with two fillers was done to obtain a hybrid composite. This system is expected to have considerable mechanical properties, good surface finish and low cost. It has been found that the tensile properties of filled epoxy were higher than unfilled epoxy. By incorporating up to 30% (by mass) Carbon fiber (CF) and 10% sawdust (SD) namely S 3 sample flexural strength was increased by 12.5%. Thus it is shown that the durability of CF/SD filled epoxy composites can be enhanced by hybridization with small amount of CF. The hybrid effects of the flexural strength and modulus were studied by the rule of hybrid mixture.

show abstract

“…The main purpose of the paper is to determine the best FRP composite from the two test pieces by comparing the tensile strength, flexural strength and impact strength and compressive strength. A.Kishore [2] studied about Epoxy (LY-556/HY-951) system filled with modified clay (MC) was synthesized by using mechanical shear mixing with the addition of hardener as tri-ethylene-tetra-amine (TETA). The effect of the fumed silica can be negated by the application of a shear force (e.g.…”

Section: Fig8: Nano Composition Of Copper Oxidementioning

confidence: 99%

Fabrication and Testing of Reinforced Natural Fiber

Srikanth¹

2018

IJRASET

View full text Add to dashboard Cite

In recent decade, bio composite materials are synthesized using natural cellulose fibers as reinforcements together with matrix, which have attracted the attention of researchers due to their low density with high specific mechanical strengths, availability, renewability, degradable and being environmental-friendly. The present work attempts to make an improvement in the current existing methodology and materials used to have better mechanical properties as well as to enhance the compatibility between fibers and the matrix using the required resin and hardener. The bio-composites are prepared with the unsaturated polyester matrix (laminate) and fibers such as dry grass, cow hair, coconut coir and nano compositions of copper oxide using wet hand lay-up method with appropriate proportions to result in fiber structure. Mechanical properties such as tensile strength, impact strength and hardness are calculated for the fabricated fiber samples.

show abstract

Hydrophilic Modified Clay Nanocomposites: Effect of Clay on Thermal and Vibrational Properties

Cited by 3 publications

References 21 publications

Effects of Performance on Mechanical Properties of Sawdust/Carbon Fibre Reinforced Polymer Matrix Hybrid Composites

Effects of Performance on Mechanical Properties of Sawdust/Carbon Fibre Reinforced Polymer Matrix Hybrid Composites

Effects of Performance on Mechanical Properties of Sawdust/Carbon Fibre Reinforced Polymer Matrix Hybrid Composites

Fabrication and Testing of Reinforced Natural Fiber

Contact Info

Product

Resources

About