Handover Latency Improvement and Packet Loss Reduction in Wireless Networks Using Scanning Algorithm

Aswathy, K.N.; Asok, Parvathy; Nandini, T.; Nair, Lekshmi S

doi:10.1007/978-981-10-8636-6_5

Cited by 3 publications

(3 citation statements)

References 10 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The papers [13,14] analyzed the improvement of packet loss reduction and handover latency in the wireless network employing scanning algorithm. This algorithm helps to minimize the handover latency and reduced the packet loss effectively, and maximizes the packet transmission rate, but the study didn't show the graphical representation of the achievements as well as the transmission time delay was not investigated.…”

Section: Switchmentioning

confidence: 99%

Analysis of performance parameters for wireless network using switching multiple access control method

Shijer

Sabry

2021

EEJET

View full text Add to dashboard Cite

The developments of wireless networks have directed to search for opportunities of a broad diversity of improved and new networking contributions. Wireless Asynchronous Transfer Mode (ATM) is a non-synchronous or random mode of transferring information. The advantages of circuit switching include dedicated connections and guaranteed traffic parameters and the benefits of packet switching are the efficiency at the physical layer and a more cost-effective design. ATM is the only protocol that offers the best of both communication methods. Although the Variable Bit-Rate (VBR) transmission presents a promising prospective of stable data quality, it is usually accompanied by network traffic overload and cell packet loss, which extensively weakens that potential. This work overcomes these concerns by developing a switching-based multiple access control model to improve the data transmission performance of wireless ATM. Therefore, this work discusses the effectiveness of the developed approach to minimize the cell packet losses and network traffic overload in wireless ATM. Three control access is processed; polling, token passing, and reservation algorithms for collision avoidance. The reservation stage reserves the data before sending, which includes two timeline intervals; a fixed-time reservation period, and variable data transmission interval. Using OPNET 10.5, the results show that the presented switching-based multiple access control model can achieve a throughput value of 98.3 %, data transmission delay of about 40.2 ms, and 0.024 % of packet losses during data transmission between the source and destination. It is demonstrated that the introduced method effectively transmits information without creating any network complexity and delay

show abstract

Section: Switchmentioning

confidence: 99%

Analysis of performance parameters for wireless network using switching multiple access control method

Shijer

Sabry

2021

EEJET

View full text Add to dashboard Cite

show abstract

“…A study that employed a scanning algorithm and handover latency improvement to analyzing packet loss within a wireless network was executed in [13]. The fundamental goal of the algorithm, as mentioned above, was to minimize packet loss while maximizing latency.…”

Section: Literature Review and Problem Statementmentioning

confidence: 99%

“…From Fig. 4, when contrasted with other methods such as packet switching (PS) [10], scanning (SC) [13],…”

Section: Packet Loss and Overhead Analysismentioning

confidence: 99%

Applying switching and multiple access model for reducing packet loss and network overheads in watm

Ali

Mshali²,

Elameer

et al. 2021

EEJET

View full text Add to dashboard Cite

As an effectual simple wireless equivalent created in the telecommunications (telephone) industry, Wireless Asynchronous Transfer Mode (WATM) is utilized to stream unified traffics like video, data, and voice data. In the asynchronous data transfer mode, voice data transfer a packet with the same medium, and data share the networks and burst data. Effective WATM data transmission requires an extensive array of designs, techniques used for control, and simulation methodologies. The congestion of the network is among the key challenges that lower the entire WATM performance during this procedure, in addition to the delay in cell and the overload of traffic. The congestions cause cell loss, and it requires expensive switches compared to the LAN. Consequently, in this current study, the application of an effectual switching model together with a control mechanism that possesses multiple accesses is employed. The multiple access process and switching model are utilized to establish an effective data sharing process with minimum complexity. The switching model uses the synchronous inputs and output ports with buffering to ensure the data sharing process. The traffic in the network is decreased, and the loss of packets in the cells is efficiently kept to a minimum by the proposed technique. The system being discussed is employed through the utilization of software employed using OPNET 10.5 simulation, with the valuation of the WATM along with the investigational outcomes accordingly. The system's efficiency is assessed by throughput, latency, cell loss probability value (CLP), overhead network, and packet loss. Thus, the system ensures the minimum packet loss (0.1 %) and high data transmission rate (96.6 %)

show abstract

Cellular Communication Network Evolution and the Reliability of System Design from 1G to 6G

Ratul,

Wang

2023

Lecture Notes on Data Engineering and Communications Technologies

View full text Add to dashboard Cite

Handover Latency Improvement and Packet Loss Reduction in Wireless Networks Using Scanning Algorithm

Cited by 3 publications

References 10 publications

Analysis of performance parameters for wireless network using switching multiple access control method

Analysis of performance parameters for wireless network using switching multiple access control method

Applying switching and multiple access model for reducing packet loss and network overheads in watm

Cellular Communication Network Evolution and the Reliability of System Design from 1G to 6G

Contact Info

Product

Resources

About