Grain size effect on the thermally activated twin boundary migration in a zirconium alloy

He, Weijun; Chen, Xin; Chen, Han; Qing, Liu

doi:10.1016/j.msea.2018.03.118

Cited by 14 publications

(1 citation statement)

References 52 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…After rolling, the average grain sizes are reduced, which may increase the CRSS of the tensile twinning as the activation of twinning was reported to be very size sensitive. [ 45,46 ] In addition, many sub‐grain boundaries are appeared, which may also contribute to the increase in the CRSS of the tensile twinning. The activation of tensile twinning with high CRSS may cause the higher compressive yield strength.…”

Section: Resultsmentioning

confidence: 99%

Microstructures and Mechanical Properties of a Commercial Pure Zirconium during Rolling and Annealing at Different Temperatures

Chen

et al. 2020

Adv Eng Mater

Self Cite

View full text Add to dashboard Cite

Zirconium (Zr) alloys have been widely applied in nuclear reactors due to their low probability of neutron capture, acceptable mechanical properties, and excellent corrosion resistance. [1-6] Zirconium alloys are commonly used as cladding tubes, fixed grids, or channel box in reactors. [2,3,6] The fabrication of Zr alloys components generally includes vacuum consumable melting, forging, extrusion, hot and cold rolling, recrystallization or stress relief annealing and so on. [7] Rolling and subsequent annealing are frequently used in the Zr alloy sheet and tube production, which actually determine the microstructure and texture, [7-10] thus playing a decisive role for the corrosion resistance, [11-14] creep resistance [15-17] and mechanical properties [18-20] of Zr alloys. Annealing can reduce the residual stress, recover the plastic deformation ability and tailor the grain size and texture, which plays a vital role in the Zr alloy fabrication. A special parameter was thus proposed to evaluate the effect of annealing. [21] The microstructure and the texture evolution during annealing are not only significantly affected by annealing condition, for example temperature [22,23] and holding time, [8,24] but also by the pre-annealing deformation. [6,25] Indeed, many research results on deformation and subsequent annealing in Zr alloys have been reported. Chen et al. [7] reported that the 30% rolling reduction combined with annealing at 580 C for 12 h imparted a superior plasticity to the Zr alloy. Kumara et al. [26] investigated the three stage of annealing in a moderately deformed Zr-4 alloy. They found that the changes in the misorientations, and corresponding rearrangements of dislocations, were the most efficient means of stress relief in Zr-4 alloy. Prakash et al. [27] investigated the microstructural and textural evolution of ZIRLO alloy during hot rolling at different temperatures. Their results show that the slip, twinning, and recrystallization played a role in the microstructure development during hot rolling. They also contributed to the texture development, lamellae break-up, and the formation of a bimodal microstructure. Jiang et al. [28] studied the effects of cold-rolling reduction, annealing temperature, and time on recrystallization behavior and kinetics of cold-rolled Zr-1Sn-0.3Nb-0.3Fe-0.1Cr alloy and found that the rate of the recrystallization increased with increasing annealing temperature and rolling reduction. Recrystallized grains nucleated preferentially at sites with high-density dislocation and deformation stored energy. Zhang et al. [29] studied the microstructure evolution and mechanical properties of Zr 98.2 Cr 1.8 during hot rolling, solution and aging treatment (STA). It was found the bimodal microstructure was the key factor to achieve high strength (ultimate tensile strength 818 MPa) and excellent ductility (18.4%) after STA at 750 C. Gerspach et al. [30] investigated the texture stability during primary recrystallization of cold-rolled Zr702 alloy and found that a small strain favored...

show abstract

Section: Resultsmentioning

confidence: 99%