Force parameters in the extrusion of tubes from a centrifugally cast semifinished product of steel 08Kh18N10T

Barichko, B. V.; Vydrin, A. V.; Kosmatskii, Ya. I.; Voskhodov, V. B.; Zubkov, A. M.

doi:10.1007/s11015-011-9423-5

Cited by 2 publications

(2 citation statements)

References 0 publications

Supporting

Mentioning

Contrasting

Unclassified

Order By: Relevance

“…Tables 1 and 2 show the actual values of technological parameters of extruding pipes of the specified assortment. Tables 1 and 2 demonstrate the values of technological parameters of extruding pipes of the specified assortment [7][8][9][10][11][12][13][14][15][16] These values were used to visualize the results and the effect of the glass-lubricating materials on pipe extrusion power parameters at bar graphs shown in Figures 6-8.…”

Section: Methods Flowmentioning

confidence: 99%

Comparative Analysis of Glass-Lubricating Materials Applied During the Pipe’s Hot-Extrusion

Kosmatskiy¹,

Krasikov²,

Tumashev³

2020

TI-IJES

View full text Add to dashboard Cite

The article presents the results of extruding pipes with the dimensions of 45.04.0 and 108.0×4.0 mm, made from 0.08 C-0.18 Cr-0.1 Ni-Ti steel with the use of proposed glass lubricants in comparison with the use of the lubricants currently used in VTZ. The comparison was made for the viscosity of glass lubricants. A research was carried out for the influence of glass-lubricating materials on the power parameters of the pipe extrusion process. A metallographic research of the front and rear ends of finished pipes was carried out, a study for the thickness distribution of glass-lubricating materials after the pipe extrusion process was carried out, an X-ray spectral analysis of glass-lubricating materials was carried out. The article presents the results of the research of the surface of finishedsize pipes in laboratory conditions. Conclusions are made about the technological features of the application of the proposed glass lubricants.

show abstract

Section: Methods Flowmentioning

confidence: 99%

Comparative Analysis of Glass-Lubricating Materials Applied During the Pipe’s Hot-Extrusion

Kosmatskiy¹,

Krasikov²,

Tumashev³

2020

TI-IJES

View full text Add to dashboard Cite

show abstract

“…С целью последующего расчета технологических параметров процесса прессования и разработки технологии рекомендуется [3] использовать максимальное значение сопротивления деформации материала. Для этого на рис.…”

unclassified

Study on the Deformation Ability Billets of Titanium Alloy Grade Pt-1m

Космацкий¹,

Фокин²,

Филяева³

et al. 2017

MET

View full text Add to dashboard Cite

Работа посвящена исследованию деформационной способности титанового сплава марки ПТ-1М. Полученные результаты исследования использованы при разработке технологии производства горячепрессованных труб. Ключевые слова: титановый сплав ПТ-1М, деформационная способность, сопротивление деформации, прессование труб. Рис. 1. Схема отбора образцов из темплетов заготовок из титанового сплава марки ПТ-1М и фотография образца с размерами Обработка металлов давлением…

show abstract

Force parameters in the extrusion of tubes from a centrifugally cast semifinished product of steel 08Kh18N10T

Cited by 2 publications

References 0 publications

Comparative Analysis of Glass-Lubricating Materials Applied During the Pipe’s Hot-Extrusion

Comparative Analysis of Glass-Lubricating Materials Applied During the Pipe’s Hot-Extrusion

Study on the Deformation Ability Billets of Titanium Alloy Grade Pt-1m

Contact Info

Product

Resources

About