Finite Element Simulation and Analysis for the Design of a Pressure Vessel with Expansion Joint

Rustam, Rafiq; Nazri, Ahmad Faiz Ahmad; Tasliman, Md Rizal Md; Mahmud, Jamaluddin

doi:10.18178/ijmmm.2018.6.4.389

Cited by 4 publications

(2 citation statements)

References 9 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Rustam et al [20] studied the effectiveness of FEA in the design and analysis of horizontal pressure vessels with and without expansion joints. The deformation and stress results obtained through ANSYS simulations were validated using mathematical approach to check the accuracy of the platform.…”

Section: Literature Reviewmentioning

confidence: 99%

Finite Element Investigation on the Performance of Pressure Vessel Subjected to Structural Load

Salins¹,

Mohan²,

Stephen³

2021

ACSM

View full text Add to dashboard Cite

Pressure vessels are highly used in industries and in commercial purposes such as filtration, boiling, softening and hot water storage tanks. Pressure vessels are subjected to thermal loads and structural loads such as internal and external pressures which leads to its deformation. Present work focusses on the modeling of the pressure vessel according to standard dimensions using CREO 6.0 and analyzing it for three different materials and different pressure values using finite element approach. The materials considered in this study for the fabrication of pressure vessel are carbon steel, stainless steel, and titanium alloy. The finite element analysis results have been presented in graphical form. Results indicated that, titanium alloy is able to withstand high stresses and exhibited high factor of safety of 4.10. And among the steels, stainless steel demonstrated low structural performance.

show abstract

Section: Literature Reviewmentioning

confidence: 99%

Finite Element Investigation on the Performance of Pressure Vessel Subjected to Structural Load

Salins¹,

Mohan²,

Stephen³

2021

ACSM

View full text Add to dashboard Cite

show abstract

“…FE analysis reveals critical information regarding the impact phenomenon which can be taken care of during experimentation and thereby reducing cost and time [6]. For the work involving optimization during the initial stages, use of software is justified [7].…”

Section: Introductionmentioning

confidence: 99%

Study on Stacking Sequence of Plies in Green Sandwiches for Low Velocity Impact Application

Mahesh

Sharnappa

Kulkarni

2019

KEM

View full text Add to dashboard Cite

The present paper deals with optimizing the stacking sequence configuration of flexible green composite for cladding application under low velocity impact regime. Initially six configurations of green composite comprising of jute fiber and natural rubber matrix are considered and their energy absorption behaviour and resistance to impact are studied using finite element analysis. The configurations considered are optimized for energy absorption and maximum contact force under low velocity impact condition. From the results it can be concluded that the variation in energy absorbed and sp. energy absorbed among the configurations are negligible and hence the configurations are prioritized based on contact force. JRJRJ configuration provides maximum contact force followed by JRJ, JRRJ, RJRJR, RJRJ and RJR. The configurations with rank 1, 2 and 3 should be taken into consideration for further analysis. Also the damage study shows that the stacking sequence with jute on impact side is better compared to rubber on impact side as tearing type of damage can be observed in sequences with rubber on impact side and no damage is visible with jute on impact side.

show abstract

Finite element analysis of bursting pressure in FRP pressure vessel

Kothali¹,

Bhapkar²,

Bhat³

2022

Materials Today: Proceedings

View full text Add to dashboard Cite

Finite Element Simulation and Analysis for the Design of a Pressure Vessel with Expansion Joint

Cited by 4 publications

References 9 publications

Finite Element Investigation on the Performance of Pressure Vessel Subjected to Structural Load

Finite Element Investigation on the Performance of Pressure Vessel Subjected to Structural Load

Study on Stacking Sequence of Plies in Green Sandwiches for Low Velocity Impact Application

Finite element analysis of bursting pressure in FRP pressure vessel

Contact Info

Product

Resources

About