Fabrication of Ti–Cu–Al coatings with amorphous microstructure on Ti–6Al–4V alloy substrate via high-energy mechanical alloying method

Chen, C.; Ding, Rui; Feng, Xiaomei; Shen, Yifu

doi:10.1016/j.surfcoat.2013.10.043

Cited by 19 publications

(1 citation statement)

References 28 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Existing references regarding amorphous coatings well cover research fields of fabrication processes, [ 52 ] microstructures, [ 53 ] mechanical behavior, corrosion, [ 54 ] and wear properties. [ 55 ] The wear behavior of amorphous coatings depends on the residual stress and adhesion of coatings, which are related to the difference in the thermal expansion coefficient between the coating and the substrate.…”

Section: Design Strategies Of Wear‐resistant Materialsmentioning

confidence: 99%

Recent Progress on Wear‐Resistant Materials: Designs, Properties, and Applications

et al. 2021

View full text Add to dashboard Cite

There has been tremendous interest in the development of different innovative wear‐resistant materials, which can help to reduce energy losses resulted from friction and wear by ≈40% over the next 10–15 years. This paper provides a comprehensive review of the recent progress on designs, properties, and applications of wear‐resistant materials, starting with an introduction of various advanced technologies for the fabrication of wear‐resistant materials and anti‐wear structures with their wear mechanisms. Typical strategies of surface engineering and matrix strengthening for the development of wear‐resistant materials are then analyzed, focusing on the development of coatings, surface texturing, surface hardening, architecture, and the exploration of matrix compositions, microstructures, and reinforcements. Afterward, the relationship between the wear resistance of a material and its intrinsic properties including hardness, stiffness, strength, and cyclic plasticity is discussed with underlying mechanisms, such as the lattice distortion effect, bonding strength effect, grain size effect, precipitation effect, grain boundary effect, dislocation or twinning effect. A wide range of fundamental applications, specifically in aerospace components, automobile parts, wind turbines, micro‐/nano‐electromechanical systems, atomic force microscopes, and biomedical devices are highlighted. This review is concluded with prospects on challenges and future directions in this critical field.

show abstract

Section: Design Strategies Of Wear‐resistant Materialsmentioning

confidence: 99%

Recent Progress on Wear‐Resistant Materials: Designs, Properties, and Applications

et al. 2021

View full text Add to dashboard Cite

show abstract

Effects of aluminum content and mechanical nano‐alloying time on the preparation of titanium‐aluminum composite coatings on magnesium‐lithium alloy

Sun

Zhu

et al. 2020

Materialwissenschaft Werkst

View full text Add to dashboard Cite

A titanium‐aluminum composite coating was successfully fabricated on magnesium‐lithium alloy substrate by mechanical nano‐alloying treatment (SMNAT). The effects of aluminum content and mechanical nano‐alloying time on the microstructure and properties of titanium‐aluminum composite coatings were investigated. The experimental results showed that the ratio of titanium‐aluminum powder has a significant effect on the preparation of the coating. Low aluminum content and high aluminum content in the mixture powder resulted in the formation of the coatings with inhomogeneous thickness. The titanium‐aluminum ratio of 3 : 1 was considered to be optimal for fabricating the coating with homogeneous thickness under the selected milling parameters. The hardness of top surface layer on titanium‐ aluminum coatings decreased from 292.0 HV 0.01 to 121.4 HV 0.01 with the increase of aluminum content. Additionally, the prolongation of treatment time facilitated to increase the thickness and density of the coatings, resulting to enhance their hardness and corrosion resistance.

show abstract

Fabrication and Characterization of Ni-SiC Nanocomposite Coatings on Al Substrates by Ball Impact Deposition Method

Yazdani

Zakeri

2017

Metall Mater Trans A

View full text Add to dashboard Cite

Fabrication of Ti–Cu–Al coatings with amorphous microstructure on Ti–6Al–4V alloy substrate via high-energy mechanical alloying method

Cited by 19 publications

References 28 publications

Recent Progress on Wear‐Resistant Materials: Designs, Properties, and Applications

Recent Progress on Wear‐Resistant Materials: Designs, Properties, and Applications

Effects of aluminum content and mechanical nano‐alloying time on the preparation of titanium‐aluminum composite coatings on magnesium‐lithium alloy

Fabrication and Characterization of Ni-SiC Nanocomposite Coatings on Al Substrates by Ball Impact Deposition Method

Contact Info

Product

Resources

About