Fabrication and characterization of A359/Al2O3 metal matrix composite using electromagnetic stir casting method

Kumar, Abhishek; Lal, Shyam; Kumar, Sudhir

doi:10.1016/j.jmrt.2013.03.015

Cited by 168 publications

(64 citation statements)

References 9 publications

Supporting

Mentioning

Contrasting

Unclassified

Order By: Relevance

“…Among the various reinforcements titanium di -boride (TiB2) is of much interest due to its excellent stiffness, hardness and wear resistance. The Aluminium metal matrix composites are produced by liquid metallurgy route such as conventional stir casting and electromagnetic stir casting [7,8]. Squeeze casting [9,10].…”

Section: Introductionmentioning

confidence: 99%

Process Parameters Optimization for Producing AA6061/TiB₂ Composites by Friction Stir Processing

Santha¹,

Ramanaiah

2017

Strojnícky Casopis – Journal of Mechanical Engineering

View full text Add to dashboard Cite

Friction stir processing (FSP) is solid state novel technique developed to refine microstructure and to improve the mechanical properties and be used to fabricate the aluminium alloy matrix composites. An attempt is made to fabricate AA6061/TiB2 aluminium alloy composite (AMCs) and the influence of process parameters like rotational speed, transverse feed, axial load and percentage reinforcement on microstructure and mechanical properties were studied. The microstructural observations are carried out and revealed that the reinforcement particles (TiB2) were uniformly dispersed in the nugget zone. The Tensile strength and Hardness of composites were evaluated. It was observed that tensile strength, and hardness were increased with increased the rotational speed and percentage reinforcement of particles. The process parameters were optimized using Taguchi analysis (Single Variable) and Grey analysis (Multi Variable). The most influential parameter was rotational speed in single variable method and multi variable optimization method. The ANOVA also done to know the percentage contribution of each parameter

show abstract

Section: Introductionmentioning

confidence: 99%

Process Parameters Optimization for Producing AA6061/TiB₂ Composites by Friction Stir Processing

Santha¹,

Ramanaiah

2017

Strojnícky Casopis – Journal of Mechanical Engineering

View full text Add to dashboard Cite

show abstract

“…The material used for light weight application. And wear resistance was performed in this work 1 .In this work aluminum 6063 material was used. The material added with Tic material.…”

Section: Introductionmentioning

confidence: 99%

Determination of White Layer Characterstics on Machining Process

Rao*,

Rao

et al. 2020

IJRTE

View full text Add to dashboard Cite

Now a day’s industries requirement as light weight and high wear resistance component. The component used as a various industrial application areas. The material also high self lubricant material also need. In this work we was used aluminium matrix composite with added in a CNT as a Nano materials. The materials has used to a high wear resistance and it is act as a self lubricant material also the material carry out different percentage and casting used in a stir casting method. The casting sample cut by a testing sample by used in an EDM wire cut machine. The sample carried out the result and plots the graphs. And the samples are carry out wear test using pin on disc method. The result shown in graph. And the sample machining study also did by EDM Wire cut machine. Finally carry out the white layer of the material. The study discussed with the paper. In this research work used in a light weight and self lubricant material needed area

show abstract

“…Aluminum (Al) metal matrix composites (AMC) have many applications in the aerospace and car industries and military applications due to their high specific modulus, high strength to weight ratio and toughness [1][2][3] . Generally, the casting, extrusion and forging routes, and powder metallurgy (PM) process have been used to produce AMC 4,5 .…”

Section: Introductionmentioning

confidence: 99%

Microwave Sintering of Aluminum-ZrB2 Composite: Focusing on Microstructure and Mechanical Properties

et al. 2016

View full text Add to dashboard Cite

Microwave assisted rapid sintering was carried out to fabricate aluminum-ZrB 2 metal matrix composites containing 1 wt% cobalt and 10, 15 and 20 wt% ZrB 2 as the reinforcements at temperatures of 600, 700 and 800°C. The results showed that the highest values of density and bending strength (97% of theoretical density and 240 MPa, respectively) were obtained in a composite containing 15 wt% ZrB 2 and 1 wt% Co sintered at 600°C. Furthermore, the optimum values of compressive strength and hardness (350 MPa and 63 Vickers, respectively) were measured for a composite containing 20 wt% ZrB 2 sintered at 600°C. At all sintering temperatures, XRD analysis revealed ZrB 2 and aluminum as the only crystalline phases. Microstructure investigations demonstrated a homogeneous distribution of ZrB 2 particles in the aluminum matrix.

show abstract

Fabrication and characterization of A359/Al2O3 metal matrix composite using electromagnetic stir casting method

Cited by 168 publications

References 9 publications

Process Parameters Optimization for Producing AA6061/TiB₂ Composites by Friction Stir Processing

Process Parameters Optimization for Producing AA6061/TiB₂ Composites by Friction Stir Processing

Determination of White Layer Characterstics on Machining Process

Microwave Sintering of Aluminum-ZrB2 Composite: Focusing on Microstructure and Mechanical Properties

Contact Info

Product

Resources

About

Fabrication and characterization of A359/Al2O3 metal matrix composite using electromagnetic stir casting method

Cited by 168 publications

References 9 publications

Process Parameters Optimization for Producing AA6061/TiB2 Composites by Friction Stir Processing

Process Parameters Optimization for Producing AA6061/TiB2 Composites by Friction Stir Processing

Determination of White Layer Characterstics on Machining Process

Microwave Sintering of Aluminum-ZrB2 Composite: Focusing on Microstructure and Mechanical Properties

Contact Info

Product

Resources

About

Process Parameters Optimization for Producing AA6061/TiB₂ Composites by Friction Stir Processing

Process Parameters Optimization for Producing AA6061/TiB₂ Composites by Friction Stir Processing