Experimental research on the thermal hydraulic characteristics of sodium boiling in an annulus

Qiu, Zicheng; Ma, Zhao; Qiu, Suizheng; Su, G.H.; Zhang, Dalin; Wu, Yingwei; Tian, Wenxi

doi:10.1016/j.expthermflusci.2014.09.016

Cited by 15 publications

(2 citation statements)

References 17 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Onwards, what is the exact boiling mechanism in Na is a subject of discussion (Qiu et al, 2015). Due to its high conductivity, it is believed that the sub-cooled boiling that happens in Light Water Reactors (LWRs) and has been the topic of much work since decades, could be negligible and that the boiling phenomenon is mainly saturated (Fujiie et al, 1976).…”

Section: Introductionmentioning

confidence: 99%

CATHARE 2 simulations of steady state air/water tests performed in a 1:1 scale SFR sub-assembly mock-up

Pérez

Alpy

Juhel

et al. 2015

Annals of Nuclear Energy

View full text Add to dashboard Cite

Section: Introductionmentioning

confidence: 99%

CATHARE 2 simulations of steady state air/water tests performed in a 1:1 scale SFR sub-assembly mock-up

Pérez

Alpy

Juhel

et al. 2015

Annals of Nuclear Energy

View full text Add to dashboard Cite

“…To investigate the onset and propagation of sodium boiling within pin bundles, various experiments have been carried out by different authors. Some of previous experimental investigations of sodium boiling are Kikuchi et al, [1], Khafizov et al [2], Qiu et al [3], Zicheng et al [4] and Katsuro et al [5]. But since sodium experiments are expensive and involve safety concerns, large volumes of numerical simulations were also reported on sodium boiling.…”

Section: Introductionmentioning

confidence: 99%

CFD Simulation of Sodium Boiling in Heated Pipe using RPI Model

Raj¹,

Velusamy²

2017

World Congress on Momentum, Heat and Mass Transfer

View full text Add to dashboard Cite

CFD prediction of sodium flow boiling in a 2-D asymmetric heated pipe is carried out using RPI wall heat flux partitioning model available in the commercial CFD code FLUENT. The two phase models are validated with published pressurized water and R12 flow boiling experimental data. The influence of radial mesh density on validation parameter is investigated. Void fraction, wall temperature and liquid temperature at different axial section are taken as the validation parameter for water experiment. Among the various parameters predicted, the void fraction of water at the outlet gave the largest deviation of 35% with experimental data. But its value is in close comparison near the location of boiling initiation. Further the void fraction calculated based on heat balance compares well with the CFD results. Radial distributions of void fraction, vapour velocity, bubble diameter at the end of heated section are the parameters compared with R12 experimental data. Except bubble diameter, all other parameters gave reasonably good comparison. But when invoking breakup and coalescence model the predicted value of bubble diameter value approaches experimental data. Finally, sodium boiling simulations were carried out with the chosen models. It was found that, unlike water and R12, in the case of sodium, stable boiling was not achieved and boiling is highly localized to the end of heated section. Periodic growth and re-condensation of sodium vapour is found. Further, temporal oscillation in the heat transfer coefficient up to 8% was observed in the boiling zone. During sodium bubble expansion the evaporative heat flux dominates and once the bubble detaches, the quenching heat flux dominates. Unlike pressurised water evaporative and quenching heat flux have almost equal participation in boiling region.

show abstract

Introduction

2021

Two‐Phase Heat Transfer

View full text Add to dashboard Cite

Experimental research on the thermal hydraulic characteristics of sodium boiling in an annulus

Cited by 15 publications

References 17 publications

CATHARE 2 simulations of steady state air/water tests performed in a 1:1 scale SFR sub-assembly mock-up

CATHARE 2 simulations of steady state air/water tests performed in a 1:1 scale SFR sub-assembly mock-up

CFD Simulation of Sodium Boiling in Heated Pipe using RPI Model

Introduction

Contact Info

Product

Resources

About