Experimental and Numerical Studies on Isothermal and Non-isothermal Deep Drawing of IS 513 CR3 Steel Sheets

Mayavan, T.; Karthikeyan, L.; Senthilkumar, V.

doi:10.1007/s11665-016-2325-8

Cited by 5 publications

(2 citation statements)

References 21 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…According to the analysis, lubricating oil viscosity and frictional coefficient were inversely related. Under heated conditions, the cup drawing test was used to examine the drawability of IS 513 CR3-grade steel sheets [10]. Analyzing the thicknesses in distinct cup-forming regions and looking at the deformation traits it was noticed that the findings are in good agreement with the experimental results in identifying the places and values of excessive thinning, which were determined by the FEA and analytical modelling results.…”

Section: Introductionmentioning

confidence: 87%

Determination of optimum process parameters for minimum punch force in deep drawing using numerical simulation

Sisil Amose,

Elsie Femina,

Sivarajan

2023

J. Phys.: Conf. Ser.

View full text Add to dashboard Cite

This article represents the most common sheet formation method, deep drawing. This technology is employed in the production of the automotive and aerospace industries. There are various aspects that have an impact on the deep drawing process; these factors are known as the deep drawing process parameters. Finite element analysis and Taguchi Techniques are coupled to find out the optimum deep drawing parameters. Six process parameters such as die corner radius, punch corner radius, punch speed, friction between blank and die, friction between blank and blank holder and friction between blank and punch are used for analysis. Punch force is considered as response variable. The Taguchi method is employed to determine the optimal process parameters for the deep drawing process. Based on SN ratio analysis, optimum deep drawing parameters for punch force were found to be die corner radius of 7mm, punch corner radius of 7mm, punch speed of 0.2mm/s, friction between blank and die of 0.08, friction between blank and blank holder of 0.08 and friction between blank and punch of 0.10. From ANOVO, it was found that die corner radius was the most significant process parameter influencing minimum punch force.

show abstract

Section: Introductionmentioning

confidence: 87%

Determination of optimum process parameters for minimum punch force in deep drawing using numerical simulation

Sisil Amose,

Elsie Femina,

Sivarajan

2023

J. Phys.: Conf. Ser.

View full text Add to dashboard Cite

show abstract

“…These facts have led to a thorough study to understand the formability behavior of this material and its nature of fracture. The room temperature formability characteristics of low CR3 grade carbon steel sheets have been already investigated in the previous work [10]. In the present investigations influence of process parameters on Limiting Drawing Ratio of IS513 CR3 grade steel sheets during warm deep drawing at 2 mm/sec, 20 mm/sec and at 50 mm/sec was studied.…”

Section: Introductionmentioning

confidence: 89%

Influence of Process Parameters on Limiting Drawing Ratio of IS513 CR3 Grade Steel Sheet during Warm Deep Drawing

Mayavan

Karthikeyan²

2014

AMR

View full text Add to dashboard Cite

In this work the significance of important parameters such as Blank temperature, Blank hold force on limiting drawing ratio (LDR) of IS513 CR3 steel sheets during warm deep drawing was determined. Influence of these parameters was analyzed at three different forming speeds. Experimental results proved that the blank temperature has a higher influence on LDR compared with other parameters especially at low forming speed.

show abstract

Experimental and numerical investigation of sheet metal failure based on Johnson-Cook model and Erichsen test over a wide range of temperatures

Nasri

Abbassi

Ahmad

et al. 2022

Mechanics of Advanced Materials and Structures

View full text Add to dashboard Cite

Experimental and Numerical Studies on Isothermal and Non-isothermal Deep Drawing of IS 513 CR3 Steel Sheets

Cited by 5 publications

References 21 publications

Determination of optimum process parameters for minimum punch force in deep drawing using numerical simulation

Determination of optimum process parameters for minimum punch force in deep drawing using numerical simulation

Influence of Process Parameters on Limiting Drawing Ratio of IS513 CR3 Grade Steel Sheet during Warm Deep Drawing

Experimental and numerical investigation of sheet metal failure based on Johnson-Cook model and Erichsen test over a wide range of temperatures

Contact Info

Product

Resources

About