Evolution of microstructure dependent corrosion properties of ultrafine AZ31 under conditions of extrusion with a forward backward oscillating die

Dobkowska, Anna; Adamczyk‐Cieślak, Bogusława; Chlewicka, Monika; Towarek, Aleksandra; Zielińska, Aleksandra; Koralnik, Milena; Kuc, D.; Mizera, Jarosław

doi:10.1016/j.jmrt.2022.04.131

Cited by 6 publications

(2 citation statements)

References 46 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…2 d). This is a typical microstructure with non-recrystallized areas (the elongated primary grains) and the small grains which were refined continuously by the dynamic recrystallization (DRX) [ [86] , [87] , [88] ]. It is clearly shown that the recrystallization processes in the valley and the tip of the screw were more intense which is, in our opinion, most likely related to the turning procedure.…”

Section: Resultsmentioning

confidence: 99%

In vitro and in vivo degradation behavior of Mg-0.45Zn-0.45Ca (ZX00) screws for orthopedic applications

Martinez

Dobkowska

Marek

et al. 2023

Bioactive Materials

Self Cite

View full text Add to dashboard Cite

Section: Resultsmentioning

confidence: 99%

In vitro and in vivo degradation behavior of Mg-0.45Zn-0.45Ca (ZX00) screws for orthopedic applications

Martinez

Dobkowska

Marek

et al. 2023

Bioactive Materials

Self Cite

View full text Add to dashboard Cite

“…2,3 Over the past few decades, various methods have been proposed to apply severe plastic strain to metal materials and convert their structure into very fine-grained or nanostructure. Some of these methods are: equal-channel angular pressing, 4,5 SPD processes using extrusion, [6][7][8] twist extrusion, 9,10 accumulative roll bonding, 11,12 and constrained groove pressing (CGP). [13][14][15] The CGP process, which is the subject of this research, is an efficient method for severe plastic deformation of sheets that has been considered by researchers in recent years.…”

Section: Introductionmentioning

confidence: 99%

Numerical-experimental study of die geometry in the constrained groove pressing of 6061 aluminum sheets

Shahri

Gholami

Rakhshkhorshid

2022

Proceedings of the Institution of Mechanical Engineers, Part B:

View full text Add to dashboard Cite

Nowadays, in line with the need of different industries to the materials with high strength to weight ratio, researchers have drawn attention to the processes of severe plastic deformation. The constrained groove pressing (CGP) is one of the most effective methods of severe plastic deformation to produce high-strength sheet metal using two dies with different shapes (grooved and flat). Despite the advantages of CGP in creating high accumulative plastic strain, this process leads to non-uniformity in mechanical properties of the sheet. This non-uniformity is one of the limitations of the CGP process which is considered in this study. Experimental and numerical studies were performed to investigate CGP process on 6061 aluminum alloy sheet up to two complete passes and the mechanical properties of the sheets were studied. Hardness testing was conducted on the worked material and the increase in the hardness of tested material in both longitudinal and thickness directions were observed. Also, it was shown that the non-uniformity in hardness distribution is correlated to the non-uniformity in the strain distribution. So, validated numerical model was used to develop the response surface method (RSM) and consequently to investigate the effect of geometric parameters in the grooved die on the strain uniformity. Finally, die geometry was optimized using the developed RSM model to produce a sample with more uniformity in strain and hardness distribution.

show abstract

Microstructure and properties of an AZ61 alloy after extrusion with a forward-backward oscillating die without preheating of the initial billet

Dobkowska

Zielińska

Paulin

et al. 2023

Journal of Alloys and Compounds

View full text Add to dashboard Cite

Evolution of microstructure dependent corrosion properties of ultrafine AZ31 under conditions of extrusion with a forward backward oscillating die

Cited by 6 publications

References 46 publications

In vitro and in vivo degradation behavior of Mg-0.45Zn-0.45Ca (ZX00) screws for orthopedic applications

In vitro and in vivo degradation behavior of Mg-0.45Zn-0.45Ca (ZX00) screws for orthopedic applications

Numerical-experimental study of die geometry in the constrained groove pressing of 6061 aluminum sheets

Microstructure and properties of an AZ61 alloy after extrusion with a forward-backward oscillating die without preheating of the initial billet

Contact Info

Product

Resources

About