Evaluation of reproducibility and reliability of 3D soft tissue analysis using 3D stereophotogrammetry

Plooij, J.M.; Swennen, G.; Rangel, Frits A.; Maal, T.J.J.; Schutyser, Filip; Bronkhorst, Ewald M.; Kuijpers-Jagtman, Anne Marie; Bergé, Stefaan

doi:10.1016/j.ijom.2008.12.009

Cited by 202 publications

(183 citation statements)

References 20 publications

Supporting

Mentioning

167

Contrasting

Unclassified

Order By: Relevance

“…In the literature, deviations are reported to be mostly caused by observer errors during placement of anthropometric points. 21,22 Plooij et al 23 found intraobserver reliability varying between 0.90 and 0.99. They found interobserver agreement above 0.8 in most points.…”

Section: Discussionmentioning

confidence: 99%

Accuracy and reliability of 3D stereophotogrammetry: A comparison to direct anthropometry and 2D photogrammetry

Di̇ndaroğlu

Kutlu

Duran

et al. 2016

The Angle Orthodontist

136

View full text Add to dashboard Cite

Objective: To evaluate the accuracy of three-dimensional (3D) stereophotogrammetry by comparing it with the direct anthropometry and digital photogrammetry methods. The reliability of 3D stereophotogrammetry was also examined. Materials and Methods: Six profile and four frontal parameters were directly measured on the faces of 80 participants. The same measurements were repeated using two-dimensional (2D) photogrammetry and 3D stereophotogrammetry (3dMDflex System, 3dMD, Atlanta, Ga) to obtain images of the subjects. Another observer made the same measurements for images obtained with 3D stereophotogrammetry, and interobserver reproducibility was evaluated for 3D images. Both observers remeasured the 3D images 1 month later, and intraobserver reproducibility was evaluated. Statistical analysis was conducted using the paired samples t-test, intraclass correlation coefficient, and Bland-Altman limits of agreement. Results: The highest mean difference was 0.30 mm between direct measurement and photogrammetry, 0.21 mm between direct measurement and 3D stereophotogrammetry, and 0.5 mm between photogrammetry and 3D stereophotogrammetry. The lowest agreement value was 0.965 in the Sn-Prn parameter between the photogrammetry and 3D stereophotogrammetry methods. Agreement between the two observers varied from 0.90 (Ch-Ch) to 0.99 (Sn-Me) in linear measurements. For intraobserver agreement, the highest difference between means was 0.33 for observer 1 and 1.42 mm for observer 2. Conclusions: Measurements obtained using 3D stereophotogrammetry indicate that it may be an accurate and reliable imaging method for use in orthodontics. (Angle Orthod. 2016;86:487-494.)

show abstract

Section: Discussionmentioning

confidence: 99%

Accuracy and reliability of 3D stereophotogrammetry: A comparison to direct anthropometry and 2D photogrammetry

Di̇ndaroğlu

Kutlu

Duran

et al. 2016

The Angle Orthodontist

136

View full text Add to dashboard Cite

show abstract

“…It has been extensively utilised in rapid prototyping [7], successfully applied in medical sciences [8,9], and is gaining popularity in multidisciplinary applications [10][11][12]. For medicine, captured digital 3D models have great accuracy and have been effectively used for facial disfigurement diagnosis, surgical planning and assessing treatment outcomes for several years [13,14]. Additionally, there is the potential to develop this automatic additive manufacture technology for facial prosthetics.…”

Section: Introductionmentioning

confidence: 99%

Colour Image Reproduction for 3D Printing Facial Prostheses

Xiao¹,

Wuerger²,

Mostafa³

et al. 2016

New Trends in 3D Printing

View full text Add to dashboard Cite

In this chapter, using colour 3D printing technology, a 3D colour image reproduction system is detailed for the semi-automated and accurate additive manufacturing of facial soft tissue prostheses. A protocol for 3D colour image reproduction was designed based on the six steps of processing. For this specific application, protocols for each subprocess required development and details of each technique applied are discussed. The quality of facial prostheses was evaluated through objective measurement and subjective assessment. The results demonstrated that the proposed colour reproduction system can be effectively used to produce accurate skin colour with fine textures over a 3D shape, with significant savings in both time and cost when compared to traditional techniques.

show abstract

“…Many studies have attempted to evaluate the relationship between hard tissue surgery and its effect on the overlying soft tissue for predicting facial changes [4][5][6]. Threedimensional (3-D) imaging techniques, including computer tomography, video imaging, laser scanning, morphanalysis, 3-D sonography, and, recently, 3-D photogrammetry [7][8][9][10][11][12][13] have been developed to highlight the relationship between hard and soft tissue movements, but details of this relationship, particularly in the vertical direction, have varied and not been fully clarified [14]. However, the assessment of visible volume changes with an optical 3-D sensor can be carried out with considerable accuracy and provides the opportunity to complete the cephalometric analysis in cases of midfacial distractions and asymmetric craniofacial situations [15].…”

Section: Introductionmentioning

confidence: 99%

Soft-Tissue Response in Orthognathic Surgery Patients Treated by Bimaxillary Osteotomy. Cephalometry Compared with 2-D Photogrammetry

Rustemeyer¹

2013

A Textbook of Advanced Oral and Maxillofacial Surgery

View full text Add to dashboard Cite

Evaluation of reproducibility and reliability of 3D soft tissue analysis using 3D stereophotogrammetry

Cited by 202 publications

References 20 publications

Accuracy and reliability of 3D stereophotogrammetry: A comparison to direct anthropometry and 2D photogrammetry

Accuracy and reliability of 3D stereophotogrammetry: A comparison to direct anthropometry and 2D photogrammetry

Colour Image Reproduction for 3D Printing Facial Prostheses

Soft-Tissue Response in Orthognathic Surgery Patients Treated by Bimaxillary Osteotomy. Cephalometry Compared with 2-D Photogrammetry

Contact Info

Product

Resources

About