Evaluation of Effect of Ti Addition to Zinc Bath on Kinetics of Growth of Alloy Layer Formed in Process of Hot-Dip Galvanisation on Steel Substrate

Bracka-Kęsek, Karolina; Szczęsny, Andrzej; Guzik, Edward; Kopyciński, Dariusz

doi:10.3390/ma16134773

Cited by 3 publications

(2 citation statements)

References 21 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Corroded components have an impact on their strength. The fracture morphology of corroded steel [48][49][50][51][52][53] revealed that as the corrosion rate increased, so did the mechanical parameters of the samples (loss in yield strength, elongation, and strength).…”

Section: Findings and Practical Implicationsmentioning

confidence: 99%

Characterization and Corrosion Behavior of Zinc Coatings for Two Anti-Corrosive Protections: A Detailed Study

Pop,

Iepure,

Titu

et al. 2023

Coatings

View full text Add to dashboard Cite

The purpose of this research is to characterize and evaluate the corrosion behavior of zinc coatings used for corrosion protection, with a special focus on the S235 steel material. The introduction highlights the need for corrosion protection in industrial settings, as well as the importance of understanding corrosion processes and the development of corrosion products to develop more effective solutions. The study’s goals are to undertake an extensive analysis of corrosion products formed on the zinc coating’s surface, to evaluate the performance of these coatings under atmospheric circumstances, and to investigate the effect of deposition parameters on coating quality. The essential message provided to readers is the critical significance of knowing corrosion product formation mechanisms and zinc coating corrosion behavior in developing long-lasting and effective protection measures. The study methodology includes cycle testing, morphological and chemical examination of corrosion products, as well as optical and electron microscopy and energy-dispersive spectroscopy. Corrosion resistance is assessed using accurate measurements. The results show that zinc coatings have exceptional corrosion resistance under air settings, with the produced corrosion products offering further protection to the underlying material. Furthermore, the study demonstrates that the surface roughness of S235 steel has a substantial impact on the quality and corrosion behavior of hot-dip galvanized coatings. The findings emphasize the necessity of detailed characterization of corrosion products, the effect of depositional factors on zinc coating performance, and the need for novel corrosion protection methods. These discoveries have significant implications for the corrosion protection sector, providing the potential to improve the longevity and efficiency of protective systems used in industrial applications.

show abstract

Section: Findings and Practical Implicationsmentioning

confidence: 99%

Characterization and Corrosion Behavior of Zinc Coatings for Two Anti-Corrosive Protections: A Detailed Study

Pop,

Iepure,

Titu

et al. 2023

Coatings

View full text Add to dashboard Cite

show abstract

“…This line of research is still being continued. Galvanizing baths are developed taking into account the specificity of materials and products, based on alloy additives that have not been used on an industrial scale before, such as Ti [4]. Alloy additives to the bath improve the technological efficiency of the hot-dip process and the quality of coatings, which reduces material costs.…”

Section: Introductionmentioning

confidence: 99%

Corrosion Behavior of Zn-Al-Mg-Si Coatings in Sulfur Dioxide-Containing Environment

Kania,

Marek

2024

Applied Sciences

View full text Add to dashboard Cite

Zn-Al-Mg-Si coatings are an excellent alternative to conventional hot-dip galvanizing coatings. Their high corrosion resistance in corrosive environments containing chlorides and CO2 is well recognized. But sulfur dioxide is also an important stimulator of corrosion in the atmospheric environment. This article presents the results of microstructure (SEM/EDS/XRD) and corrosion behavior tests of Zn-Al-Mg-Si coatings obtained by a double hot-dip method on HSLA steel. The corrosion resistance of the coatings was determined in the sulfur dioxide test with general condensation of moisture (EN ISO 6988). In the corrosion test, Zn-Al-Mg-Si coatings showed twofold smaller weight loss compared to conventional hot-dip zinc coatings. It was found that the corrosion behavior of coatings was influenced by the structural components revealed in the outer layer: Al-rich dendritic and interdendritic areas with Zn/MgZn2 eutectic, MgZn2 intermetallic and Si precipitates and their electrochemical nature. The increase in corrosion resistance was caused by the formation of beneficial corrosion products: layered double hydroxides (LDHs) based on divalent Mg2+ and Zn2+ cations, trivalent Al3+ cations and SO42− anions, and zinc hydroxysulfate—Zn4SO4(OH)6∙5H2O. The presence of Si precipitates could cause pitting corrosion of coatings.

show abstract

Effect of antimony additions on the microstructure and performance of Zn–Mg–Al alloy coatings

Britton,

Penney,

Malla

et al. 2024

npj Mater Degrad

View full text Add to dashboard Cite

Microscopy, electrochemical techniques and mechanical testing are used to investigate the effect of varying antimony additions (0.45–1.8 wt%) on the microstructure and corrosion properties of zinc-magnesium-aluminium coating alloys. Samples were produced by splat casting to produce high cooling rates similar to those seen in a continuous galvanising line. X-Ray Microscopy reveals that the Sb additions produce disk-shaped Mg3Sb2 intermetallics, subsequently reducing or eliminating the MgZn2 eutectic. Electrochemical testing in 1 wt% NaCl shows that the Mg3Sb2 phase is cathodic with respect to the bulk alloy with slower oxygen reduction kinetics. The decrease in eutectic content leads to less intense anodic activity. The combined effect is anodic and cathodic deactivation, which leads to a 43% reduction in corrosion rate as measured through LPR compared to the base alloy. This work shows that quaternary additions to ZMA coating alloys can be a potential route to improved corrosion resistance for galvanic protection.

show abstract

Evaluation of Effect of Ti Addition to Zinc Bath on Kinetics of Growth of Alloy Layer Formed in Process of Hot-Dip Galvanisation on Steel Substrate

Cited by 3 publications

References 21 publications

Characterization and Corrosion Behavior of Zinc Coatings for Two Anti-Corrosive Protections: A Detailed Study

Characterization and Corrosion Behavior of Zinc Coatings for Two Anti-Corrosive Protections: A Detailed Study

Corrosion Behavior of Zn-Al-Mg-Si Coatings in Sulfur Dioxide-Containing Environment

Effect of antimony additions on the microstructure and performance of Zn–Mg–Al alloy coatings

Contact Info

Product

Resources

About