Enhancing the Mechanical Properties of Waterborne Polyurethane Paint by Graphene Oxide for Wood Products

Xu, Dandan; Liang, Guotao; Qi, Yanran; Gong, Ruizhi; Zhang, Xingquan; Liu, Baoxuan; Kong, Linglong; Dong, Xiaoying; Li, Yongfeng

doi:10.3390/polym14245456

Cited by 11 publications

(9 citation statements)

References 55 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The requirements for the flatness and roughness uniformity of the substrate are relatively high [ 45 , 46 ]. As a protective coating, it is often subject to friction, impact, tension, and other forces, so the coating film is required to have necessary mechanical properties [ 47 , 48 ]. The mechanical characteristics of the coating film of the andoung wood surface are summarized in Table 9 .…”

Section: Resultsmentioning

confidence: 99%

Preparation of Antibacterial Nanosilver Solution Microcapsules and Their Impact on the Performance of Andoung Wood Surface Coating

Pan

Yan

2023

Polymers

View full text Add to dashboard Cite

In this paper, nanosilver solution was used as an antibacterial agent to prepare antibacterial microcapsules. The mass ratio of the core material to the wall material (Wcore: Wwall), the emulsifier’s hydrophilic–lipophilic balance (HLB) value, the mass ratio of ethanol to the emulsifier in solvent (Wcore: Wemulsion), and the rotational speed (r/min) were used to develop the four-factor, three-level orthogonal experiment, which was meant to investigate the most significant factors and the optimum process preparation parameters impacting the coating rate and yield of microcapsules. It was used to make an antibacterial coating that was applied to the surface paint film of a glass substrate and andoung wood, and it was mixed to the water-based primer with a content of 4%. Analyses of the mechanical, optical, and bactericidal characteristics were conducted. The micromorphology of the nanosilver solution microcapsules is influenced by the emulsifier’s HLB value. The color difference of the antibacterial coating film decreased with increasing emulsifier HLB value; however, the coating film’s gloss remained largely suitable. Additionally, the coating film’s transparency and tensile strength both decreased. It had minimal impact on the paint film’s surface hardness, but the adhesion and tensile strength showed a noticeable downward trend. The surface of the paint film was rough. Escherichia coli and Staphylococcus aureus were resistant to the antibacterial characteristics of the water-based primer film when it was combined with antibacterial nanosilver solution microcapsules by 80.7% and 74.55%, respectively. The coating film’s antibacterial properties were applied to the surface of the andoung wood, which were 75.7% and 71.0%, respectively, and somewhat decreased. In order to successfully inhibit bacteria, the nanosilver solution microcapsules were added to waterborne coatings. This ensures both the outstanding performance of the coating film and the effectiveness of the antibacterial effect. It expands the application prospects of antibacterial microcapsules in coatings.

show abstract

Section: Resultsmentioning

confidence: 99%

Preparation of Antibacterial Nanosilver Solution Microcapsules and Their Impact on the Performance of Andoung Wood Surface Coating

Pan

Yan

2023

Polymers

View full text Add to dashboard Cite

show abstract

“…In another study by Xu et al [6], the use of graphene oxide as an addition to polyurethane paints used for finishing furniture resulted in a significant increase in the hardness of the coating and scratch resistance. In turn, Han et al [7] focused on analyzing the impact of graphene oxide on changes in the flammability of wood, indicating that it may play an important role in fire protection.…”

Section: Introductionmentioning

confidence: 99%

Graphene Oxide as a Factor Modifying the Properties of Wood

Betlej,

Andres,

Borysiak

et al. 2024

Coatings

View full text Add to dashboard Cite

This work carried out research to determine the possibilities of using graphene oxide to provide wood with new functional features. With the saturation parameters used and working liquid with a concentration of 0.004% graphene oxide, the retention of the nanomaterial in wood was 0.25 kg/m3. The presence of graphene oxide increased the crystallinity of the wood to 64% (compared with 57% for unmodified wood). The TG/DTG spectra of wood impregnated with graphene oxide and the control wood indicated that the initial weight loss of the samples observed at a temperature of 100 °C was similar and amounted to less than 4%. A second mass loss was observed in a temperature range of 270 to 380 °C. The mass loss in this temperature range reached 70% and was similar in the test and control samples. Wood modified with graphene oxide showed increased thermal stability in a temperature range of 360 to 660 °C compared with native wood. Given the results obtained, there were no statistically significant differences in the water absorption of modified or control wood. The presence of low concentrations of graphene oxide in the culture medium did not inhibit the growth of the fungus Trichoderma viride; however, a decrease in the growth activity of mycelial hyphae was observed with an increasing concentration of nanomaterial in the medium. It has been reported that graphene oxide, as a stress factor, initiates changes at the cellular level, characterized by the formation of structures called chlamydospores by the body.

show abstract

“…However, biodegradable plastics have limitations in practicality due to difficulty in molding or poor physical properties [ 4 , 5 , 6 ]. Accordingly, the current trend has been progressively towards extensive research on waterborne polyurethane (WPU) as a replacement for solvent-borne polyurethanes (PUs) [ 7 , 8 ]. Waterborne polyurethane (WPU) has been substituted in existing PUs involved in the issue of organic solvents due to the increasing attention to health and environmental issues.…”

Section: Introductionmentioning

confidence: 99%

In Situ Synthesis of Environmentally Friendly Waterborne Polyurethane Extended with Regenerated Cellulose Nanoparticles for Enhanced Mechanical Performances

Choi

Lee

et al. 2023

Polymers

View full text Add to dashboard Cite

The development of waterborne polyurethane (WPU) has been stimulated as an alternative to solvent-based polyurethanes due to low-VOC alternatives and reduced exposure to solvents. However, their relatively low mechanical performance and degradation have presented challenges in their wide application. Here, we developed environmentally-friendly bio polyol-based WPU nanocomposite dispersions and films, and presented the optimal process conditions for their manufacture. Additionally, the condition was established without using harmful catalysts or ethyl methyl ketone (MEK) during the polymerization. Moreover, regenerated cellulose nanoparticles (RCNs) were employed as natural chain-extenders in order to improve the biodegradability and mechanical performances of the nanocomposite films. The RCNs have a lower crystallinity compared to cellulose nanocrystals (CNCs), allowing them to possess high toughness without interfering with the elastomeric properties of polyurethane. The prepared CWPU/RCNs nanocomposite films exhibited high toughness of 58.8 ± 3 kgf∙mm and elongation at break of 240 ± 20%. In addition, depending on the molar ratio of NCO/OH, the polyurethane particle size is variously controlled from 70 to 230 nm, enabling to fabricate their dispersions with various transmittances. We believe that our findings not only open a meaningful path toward green elastomers with biodegradability but provides the design concept for bio-elastomers in order to develop industrial elastomers with mechanical and thermal properties.

show abstract

Enhancing the Mechanical Properties of Waterborne Polyurethane Paint by Graphene Oxide for Wood Products

Cited by 11 publications

References 55 publications

Preparation of Antibacterial Nanosilver Solution Microcapsules and Their Impact on the Performance of Andoung Wood Surface Coating

Preparation of Antibacterial Nanosilver Solution Microcapsules and Their Impact on the Performance of Andoung Wood Surface Coating

Graphene Oxide as a Factor Modifying the Properties of Wood

In Situ Synthesis of Environmentally Friendly Waterborne Polyurethane Extended with Regenerated Cellulose Nanoparticles for Enhanced Mechanical Performances

Contact Info

Product

Resources

About