Enhancement of poly(phenyl sulfone) membranes with ZnO nanoparticles

Alsalhy, Qusay F.; Ali, Jamal M.; Abbas, Ali A.; Rashed, Ali; Bruggen, Bart Van der; Baltă, Ștefan

doi:10.1080/19443994.2013.764487

Cited by 43 publications

(32 citation statements)

References 21 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…However, the slight difference in mean pore size and thickness of these three membranes (see Table 3 and Figure 7) was the real reason behind these results. This occurred because the addition of PES enhanced the membrane morphology and structure, including the pore size, pore size distribution, contact angle, and surface roughness [7].…”

Section: Dye Removal Efficiency Of the Ppsu-pes Membranesmentioning

confidence: 99%

“…Membranes 2019, 9, x FOR PEER REVIEW 16 of 18 enhanced the membrane morphology and structure, including the pore size, pore size distribution, contact angle, and surface roughness [7]. The permeation fluxes were greatly enhanced with high dye removal efficiency of the simulated wastewater by the addition of PES as a polymer blend.…”

Section: Dye Removal Efficiency Of the Ppsu-pes Membranesmentioning

confidence: 99%

“…Contaminant (e.g., heavy metals) rejection was completed by complexing the metal ions with polyaziridine, which has displayed a good rejection of 99.5% and 95.5% of Pb 2+ and Cd 2+ , respectively. Since 2012, poly phenyl sulfone (PPSU) emerged as an excellent polymer material for membrane fabrication due to its advantageous characteristics, especially for NF application [7]. From the earlier reports about PPSU, membrane fabrication confirms that a key drawback was a lack of mechanical stability, which is crucial for separation efficiency and lifespan.…”

mentioning

confidence: 99%

See 2 more Smart Citations

Removal of Dye from a Leather Tanning Factory by Flat-Sheet Blend Ultrafiltration (UF) Membrane

et al. 2020

Self Cite

View full text Add to dashboard Cite

In this work, a flat-sheet blend membrane was fabricated by a traditional phase inversion method, using the polymer blends poly phenyl sulfone (PPSU) and polyether sulfone (PES) for the ultrafiltration (UF) application. It was hypothesized that adding PES to the PPSU polymer blend would improve the properties of the PPSU membrane. The effect of the PES concentration on the blend membrane properties was investigated extensively. The characteristics of PPSU-PES blend membranes were investigated using atomic force microscopy (AFM), scanning electron microscopy (SEM), contact angle measure, and contaminant (dye) elimination efficiency. This study showed that PES clearly affected the structural formation of the blended membranes. A considerable increase in the average roughness (about 93%) was observed with the addition of 4% PES, with a higher mean pore size accompanied by a rise in the pores' density on the surface of the membrane. The addition of up to 4% PES had a significant influence on the hydrophilic character of the PPSU-PES membrane, by lowering the value of the contact angle (CA) (i.e., to 56.9 • ). The performance of the PPSU-PES composite membranes' UF performance was systematically investigated, and the membrane pure water permeability (PWP) was enhanced by 25% with the addition of 4% PES. The best separation removal factor achieved in the current investigation for dye (Drupel Black NT) was 96.62% for a PPSU-PES (16:4 wt./wt.%) membrane with a 50% feed dye concentration.Membranes 2020, 10, 47 2 of 17 the removal of a variety of dye molecules from industrial effluents. Hence, a number of investigations have reported using UF and nanofiltration technologies in textile manufacturing industries [4].Alventosa-deLara et al.[5] studied the influence of trans-membrane pressure (TMP) and cross-flow velocity (CFV) on the ultrafiltration (UF) ceramic membrane performance for various concentrations of dye (50-500 ppm). They concluded that the permeate flux increases with a higher TMP and CFV as well as with a low concentration of feed, up to a maximum flux of 0.267 m 3 /(m 2 h). Moreover, the efficiency of the UF treatment was estimated by the dye rejection coefficient. Alventosa-deLara et al. [5] reported considerable dye rejection, regardless of the examined conditions, with steady-state rejection higher than 79.9% for 50 ppm and approximately 73.2% for 500 ppm. Moideen et al.[6] prepared a polysulfone-poly phenyl sulfone (PSF-PPSU blend UF membrane for Pb 2+ and Cd 2+ heavy metal removal, and the blend membrane displayed improved performance and hydrophilicity as well as an antifouling feature, as compared with the pristine PSF polymer membrane. Contaminant (e.g., heavy metals) rejection was completed by complexing the metal ions with polyaziridine, which has displayed a good rejection of 99.5% and 95.5% of Pb 2+ and Cd 2+ , respectively. Since 2012, poly phenyl sulfone (PPSU) emerged as an excellent polymer material for membrane fabrication due to its advantageous characteristics, especially for NF application [...

show abstract

Section: Dye Removal Efficiency Of the Ppsu-pes Membranesmentioning

confidence: 99%

Section: Dye Removal Efficiency Of the Ppsu-pes Membranesmentioning

confidence: 99%

mentioning

confidence: 99%

See 1 more Smart Citation

Removal of Dye from a Leather Tanning Factory by Flat-Sheet Blend Ultrafiltration (UF) Membrane

et al. 2020

Self Cite

View full text Add to dashboard Cite

show abstract

“…PI hollow fiber membrane was subjected to extensive surface analysis using an AFM of Angstrom Advanced Inc. (United States), model AA3000, in contact mode with a suitable silicon tip. All information about the AFM measurements was explained in details elsewhere …”

Section: Experimental Workmentioning

confidence: 99%

“…All information about the AFM measurements was explained in details elsewhere. 22,24 Pure Water Permeability (PWP) and Solutes Rejection The performance of PI hollow fiber membranes was conducted using cross-flow filtration unit as shown in Figure 1. Three hol-low fiber membranes of each type were tested under 1 bar transmembrane pressure and 600 mL/min feed flow rate.…”

Section: Preparation Of Dope Solution and Pi Hollow Fiber Nf Membranesmentioning

confidence: 99%

Effect of the preparation conditions on the morphology and performance of poly(imide) hollow fiber membranes

Alsalhy

Salih

Melkon³

et al. 2014

J of Applied Polymer Sci

Self Cite

View full text Add to dashboard Cite

Poly(imide) (PI) hollow fiber membranes were prepared by using classical phase inversion process. Effects of different external coagulation bath temperatures (ECBT) and various bore flow rates (BFR) on the morphology and separation performance of the membranes were studied. Cross‐section, inner and outer structures were characterized by using scanning electron microscope and atomic force microscopy (AFM). Mean pore size, pore size distribution, and mean roughness of the PI hollow fibers surfaces were estimated by AFM. It was found that the hollow fibers morphology composed of sponge‐like and finger‐like structures with different ECBT and BFR. A circular shape of the nodules with different sizes was observed in the outer surface of the PI hollow fibers. Mean pore size of the outer surface increases with increasing ECBT and BFR. The important result observed in this study is that the ECBT clearly has the largest effect on hollow fiber PI membrane roughness compared with the BFR. Pure water permeability of the PI hollow fibers was improved with increase of ECBT and BFR. The solute rejection (R%) was reduced when the ECBT and BFR was increased. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014, 131, 40428.

show abstract

Nanotechnology Solutions for Public Water Challenges

Dhillon

Kumar

2018

Nanotechnology for Sustainable Water Resources

View full text Add to dashboard Cite

Enhancement of poly(phenyl sulfone) membranes with ZnO nanoparticles

Cited by 43 publications

References 21 publications

Removal of Dye from a Leather Tanning Factory by Flat-Sheet Blend Ultrafiltration (UF) Membrane

Removal of Dye from a Leather Tanning Factory by Flat-Sheet Blend Ultrafiltration (UF) Membrane

Effect of the preparation conditions on the morphology and performance of poly(imide) hollow fiber membranes

Nanotechnology Solutions for Public Water Challenges

Contact Info

Product

Resources

About