Enhanced interfacial strength and ductility of stainless steel/carbon steel laminated composite by heterogenous lamella structure

Yang, Yaohua; Jiang, Zizheng; Li, Xuefeng; Sun, Jingdong; Wang, Wenjing

doi:10.1016/j.jmrt.2022.04.057

Cited by 17 publications

(1 citation statement)

References 49 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The rolling composite method of stainless-clad bimetallic steels Among those methods, the rolling compound method is the earliest and most widely used manufacturing process (Jing et al, 2022;Jiang et al, 2018;Yang et al, 2022). The rolling compound method can achieve large economic and efficient production, which is suitable for mass production of steel plates with different thicknesses; it also has excellent interface bonding properties.…”

Section: 2mentioning

confidence: 99%

Review on the application of stainless-clad bimetallic steel in the marine environment

Wang,

Sun,

Jiang

et al. 2024

ACMM

View full text Add to dashboard Cite

Purpose Stainless-clad bimetallic steels (SCBS) are widely investigated in some extremely environmental applications areas, such as polar sailing area and tropical oil and gas platforms areas, because of their excellent anticorrosion performance and relatively lower production costs. However, the properties of SCBS, including the mechanical strength, weldability and the anticorrosion behavior, have a direct relation with the manufacturing process and can affect their practical applications. This paper aims to review the application and the properties requirements of SCBS in marine environments to promote the application of this new material in more fields. Design/methodology/approach In this paper, the manufacturing process, welding and corrosion-resistant properties of SCBS were introduced systematically by reviewing the related literatures, and some results of the authors’ research group were also introduced briefly. Findings Different preparation methods, such as rolling composite, casting rolling composite, explosive composite, laser cladding and plasma arc cladding, as well as the process parameters, including the vacuum degree, rolling temperature, rolling reduction ratio, volume ratios of liquid to solid, explosive ratio and the heat treatment, influenced a lot on the properties of the SCBS through changing the interface microstructures. Otherwise, the variations in rolling temperature, pass, reduction and the grain size of clad steel also brought the dissimilarities of the mechanical properties, microhardness, bonding strength and toughness. Another two new processes, clad teeming method and interlayer explosive welding, deserve more attention because of their excellent microstructure control ability. The superior corrosion resistance of SCBS can alleviate the corrosion problem in the marine environment and prolong the service life of the equipment, but the phenomenon of galvanic corrosion should be noted as much as possible. The high dilution rate, welding process specifications and heat treatment can weaken the intergranular corrosion resistance in the weld area. Originality/value This paper summarizes the application of SCBS in marine environments and provides an overview and reference for the research of stainless-clad bimetallic steel.

show abstract

Section: 2mentioning

confidence: 99%

Review on the application of stainless-clad bimetallic steel in the marine environment

Wang,

Sun,

Jiang

et al. 2024

ACMM

View full text Add to dashboard Cite

show abstract

Bonding Behavior and Mechanism of Composite Interface Between Carbon Steel/Stainless Steel Laminates at Different Temperatures and Strain Rates

Hu,

Song,

Yang

et al. 2024

steel research int.

View full text Add to dashboard Cite

Compared to hot roll and explosive bonding, there are relatively few studies on warm/cold roll bonding under low temperature conditions. In this article, the warm/cold roll bonding simulation experiment is conducted to research the deformation, interface bonding rate, microstructure, element diffusion behavior, metallographic structure, and phase of carbon steel/stainless steel. The results show that the plastic deformation remains consistent below 400 °C but exhibits temperature sensitivity above 400 °C. The lower strain rate can increase the bonding rate, while insulation treatment may reduce the bonding rate. The formation of cracks is inhibited at 25 °C and 45% reduction rate due to the challenge of cracking the surface oxide film. Temperature significantly affects bonding, with improved performance observed above 600 °C. Uneven element distribution of bonding area may be related to the precipitated compounds, while insulation treatment increases the mutual diffusion ability of elements. The increase in temperature leads to an increase in pearlite, a decrease in ferrite, and decarburization occurs within the carbon steel matrix. The carbon elements diffuse from carbon steel to the surface of stainless steel. The increase in temperature increases the content of surface compounds.

show abstract

Failure Mechanisms in Stainless Steel/Carbon Steel Clad Plate Under Shear Tensile Loading: Experimental and Modeling Methods

Liu,

Ding,

et al. 2024

steel research int.

View full text Add to dashboard Cite

The deformation behavior of a stainless steel/carbon steel (SS/CS) clad plate under interface shear loading is characterized in this work. A 2D digital image correlation method is applied to track the strain field variation near the interface during shear tensile tests. Then, a cohesive zone model (CZM) finite‐element method is developed to clarify the delamination behavior of the tested clad plate. Finally, the interfacial failure characteristics of the SS/CS clad plate are further presented through the comparison between the finite‐element method and fractography analysis at the interface. In the experimental and simulation results, it is shown that the mixed‐mode CZM, which couples the constitutive equations of three fracture modes, demonstrates excellent capabilities in capturing SS/CS interfacial deformation behavior. The main deformation mode in shear tensile tests is variable according to locations. The central region at the bonded surface is dominated by the shear delamination mode, and the region near the notches shows shifted crack propagation toward normal mode. These abrupt interfacial failures can be clarified via stress state and local damage analysis of the well‐reproduced finite‐element model of cladding material.

show abstract

Enhanced interfacial strength and ductility of stainless steel/carbon steel laminated composite by heterogenous lamella structure

Cited by 17 publications

References 49 publications

Review on the application of stainless-clad bimetallic steel in the marine environment

Review on the application of stainless-clad bimetallic steel in the marine environment

Bonding Behavior and Mechanism of Composite Interface Between Carbon Steel/Stainless Steel Laminates at Different Temperatures and Strain Rates

Failure Mechanisms in Stainless Steel/Carbon Steel Clad Plate Under Shear Tensile Loading: Experimental and Modeling Methods

Contact Info

Product

Resources

About