Electromigration Behavior of through-Si-via (TSV) Interconnect for 3-D Flip Chip Packaging

Ha, Sang-Su; Yang, Jun‐Mo; Jung, Seung‐Boo

doi:10.2320/matertrans.m2009367

Mater. Trans.

2010

DOI: 10.2320/matertrans.m2009367

|View full text |Cite

Electromigration Behavior of through-Si-via (TSV) Interconnect for 3-D Flip Chip Packaging

Sang-Su Ha

Jun‐Mo Yang

Seung‐Boo Jung

Help me understand this report

Search citation statements

Order By: Relevance

Paper Sections

Select...

Citation Types

Supporting

Mentioning

Contrasting

Year Published

2017

Publication Types

Select...

Article1

Relationship

Self Cite0

Independent1

Authors

Journals

Cited by 1 publication

(1 citation statement)

References 21 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…8 The use of three-dimensional (3D) packaging through-silicon via (TSV) technology allows a high density of vertical interconnects, unlike 2D packing, as shown in Figure 1. 3D TSV ICs have the following advantages: (1) reduced connection lengths, and thus smaller parasitic capacitance, inductance, and resistance; (2) high-speed low-power interconnects; and (3) a combination of monolithic and multifunctional integration.…”

mentioning

confidence: 99%

Through-Silicon via Submount for Flip-Chip LEDs

Chang

Chen

et al. 2017

ECS J. Solid State Sci. Technol.

View full text Add to dashboard Cite

A blue light emitting diode (LED) was prepared by a flip-chip (FC) LED and three-dimensional through-silicon via (3D-TSV) technique. The experimental results indicated that the diameter and length of the Si via were about 180 μm and 400 μm, respectively. The Cu was uniformly and high density filled in each TSV, and the average resistance was about 0.14 m . It was also found that the 96.43Sn-3.57at%Ag bumps were electroplated on the Cu plugged TSVs of a silicon substrate, and these were smoother at 250 • C. After reflow, a 3D blue light emitting diode was prepared by peak bonding at 250 The increasing use of light emitting diodes (LED) in products has promoted the development of higher power, greater density, and lower cost devices. Compared with conventional LED, flip-chip (FC) LED 1-3 have a number of advantages, such as about twice the light output of conventional LED. Flip-chip technology not only shortens the production process, but also significantly reduces thermal resistance and results in a greater heat dissipation rate than seen with the traditional gold wire bonded LED. Moreover, the direct contact of the electrodes or bumps with the package structure can substantially enhance the cooling effect. The flip-chip approach can also remove wire bonding and other wire frame processes, and so these LED can be used with high current drivers.4,5 Therefore, FC LED are attracting growing interest due to their greater heat dissipation, better light emission, higher reliability, and more efficient bonding processes than seen with traditional wire bonded LED.The typical bonding process recommended by chip companies for FC LED is Au/Sn eutectic bonding.6 However, eutectic Sn-Ag alloy is a promising candidate among the various Pb-free solder materials for use with FC LED, and the resulting Sn-Ag alloy bumps 7 can be easily obtained by annealing the Ag/Sn metal stack.There is also demand for new packaging processes for FC LED. 8The use of three-dimensional (3D) packaging through-silicon via (TSV) technology allows a high density of vertical interconnects, unlike 2D packing, as shown in Figure 1. 3D TSV ICs have the following advantages: (1) reduced connection lengths, and thus smaller parasitic capacitance, inductance, and resistance; (2) high-speed low-power interconnects; and (3) a combination of monolithic and multifunctional integration. In this study, a blue LED was prepared using an FC LED and the 3D-TSV technique. We thus propose a new method to achieve 3D LED packing. The detailed fabrication of the TSV and the electrooptical properties of the fabricated are also discussed. ExperimentalFigure 2 presents a schematic diagram of the fabrication process for the 3D LED. A P-type 400 μm thick Si wafer was used as the bottom substrate. Photolithography was used to make a mask for etching the Al layer. A positive type photoresist, AZ-1500, was spin-coated to a thickness of 2 μm with a rotation speed of 500 rpm for 15 s, followed by 3000 rpm for 30 s. The Al layer was etched by wet etching, after using acetone to remove...

show abstract

mentioning

confidence: 99%

Through-Silicon via Submount for Flip-Chip LEDs

Chang

Chen

et al. 2017

ECS J. Solid State Sci. Technol.

View full text Add to dashboard Cite

show abstract

scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.

Contact Info

hi@scite.ai

10624 S. Eastern Ave., Ste. A-614

Henderson, NV 89052, USA

Blog Terms and Conditions API Terms Privacy Policy Contact Cookie Preferences Do Not Sell or Share My Personal Information

Made with 💙 for researchers

Part of the Research Solutions Family.

Electromigration Behavior of through-Si-via (TSV) Interconnect for 3-D Flip Chip Packaging

Cited by 1 publication

References 21 publications

Through-Silicon via Submount for Flip-Chip LEDs

Through-Silicon via Submount for Flip-Chip LEDs

Contact Info

Product

Resources

About