Efficiencies and improvement potential of building integrated photovoltaic thermal (BIPVT) system

Ibrahim, Adnan; Fudholi, Ahmad; Sopian, Kamaruzzaman; Othman, Masuri; Ruslan, Mohd Hafidz

doi:10.1016/j.enconman.2013.10.033

Cited by 223 publications

(73 citation statements)

References 37 publications

Supporting

Mentioning

Contrasting

Unclassified

Order By: Relevance

“…Beberapa penyelidik telah membina dan menilai prestasi pengumpul PV/T aliran air Ibrahim et al 2014Ibrahim et al , 2009Mishra et al 2013). Tripanagnostopoulos et al (2002) telah membuat kajian menguji kecekapan pengumpul PV/T aliran air terhadap dua jenis sel suria iaitu a-Si dan c-Si.…”

Section: Pengenalanunclassified

Kecekapan Pengumpul PV/T menggunakan Pengumpul Terma Reka Bentuk Pilin

Aisyah

Fudholi²,

Othman³

et al. 2018

JSM

Self Cite

View full text Add to dashboard Cite

AbstrAk Kajian ini bertujuan untuk mereka bentuk dan mengkaji prestasi pengumpul fotovoltan-terma (PV/T) dengan This study aimed to design and assess the photovoltaic-thermal (PV/T) collector performance using spiral thermal collector design. The design of the spiral water collector was rebuilt from previous researchers design. The thermal collectors use a larger tube size and the distance between the tubes closer than with previous researchers design. PV

show abstract

Section: Pengenalanunclassified

Kecekapan Pengumpul PV/T menggunakan Pengumpul Terma Reka Bentuk Pilin

Aisyah

Fudholi²,

Othman³

et al. 2018

JSM

Self Cite

View full text Add to dashboard Cite

show abstract

“…The PV-battery power sources are generally used to provide electric energy for local consumers such as buildings. For example, they are widely used in building integrated photovoltaic systems (BIPVS) [1]. The PV-battery power sources are strictly different from grid-connected PV systems, so that, maximum power point tracking (MPPT) schemes cannot be applied to them because the output current of the PV panel is only determined by the state of charge (SOC) of the batteries bank which is the sole load of the PV panel.…”

Section: Introductionmentioning

confidence: 99%

Two novel techniques for increasing energy efficiency of photovoltaic-battery systems

Fathabadi

2015

Energy Conversion and Management

View full text Add to dashboard Cite

“…Solar energy is a clean energy which has the potential to meet a significant proportional of the world's energy needs (Fudholi et al, 2014b;2014c). It can be broadly classified into two systems; thermal energy system which converts solar energy into thermal energy, and photovoltaic (PV) energy system which converts solar energy into electrical energy (Ibrahim et al, 2014;Fudholi et al, 2013a;2013b).…”

Section: Introductionmentioning

confidence: 99%

Design Maximum Power Point Tracking (MPPT) on Photovoltaic Panels using Fuzzy Logic Method

Faizal

Sutoyo

Mulyono

et al. 2016

American Journal of Engineering and Applied Sciences

Self Cite

View full text Add to dashboard Cite

Solar energy is a clean energy, renewable, and available for the long term. The tool used to convert the energy generated from the intensity of sunlight into electricity is photovoltaic panels. However, due to the high cost and low efficiency, the use of the energy is still kind small compared to other types of energy sources. Thus, the need for an effective and flexible models, which resemble the characteristics of the actual photovoltaic (PV), so that we can perform simple manipulation of some data to figure out how to get the maximum performance possible. The characteristic of the solar panel output is specific and non-linear, it depend on the solar irradiation and the temperature of the solar panel. Because of it, it makes us difficult to get the Maximum Power Point (or abbreviated MPP) of the solar panels. Approach: Therefore, to solve these problems required the modeling of the solar panel for design and simulate the algorithms of Maximum Power Point Tracking (MPPT) to maintain the working point of solar panels fixed on the MPP. Overall, the designed system results carried are running well. The increase in the average value of the output voltage by 17%, from an average of 11.6 V before installation into 13.94 V after installation MPPT system. It also occurs in output power with an increase of 28%, from an average of 35.13 W before installing system MPPT into 48.9 W after installation MPPT system. The temperature effect on module voltage and output power before and after installation of the MPPT system that after the installation of the MPPT system, the voltage output of photovoltaic modules can be maintained around the desired maximum value that's equal to 12 V. But there was a drop in output power value compared to the prior installation MPPT system. This is caused by the output current value that cannot accommodate the value of the output voltage. So that the value of the output current is enough to produce the maximum output power is needed quantities corresponding load.

show abstract

Efficiencies and improvement potential of building integrated photovoltaic thermal (BIPVT) system

Cited by 223 publications

References 37 publications

Kecekapan Pengumpul PV/T menggunakan Pengumpul Terma Reka Bentuk Pilin

Kecekapan Pengumpul PV/T menggunakan Pengumpul Terma Reka Bentuk Pilin

Two novel techniques for increasing energy efficiency of photovoltaic-battery systems

Design Maximum Power Point Tracking (MPPT) on Photovoltaic Panels using Fuzzy Logic Method

Contact Info

Product

Resources

About