Effects of TiO2 and Co2O3 combination additions on the elemental distribution and electromagnetic properties of Mn–Zn power ferrites

Yang, Wenda; Wang, Y.G.

doi:10.1016/j.jmmm.2015.02.020

Cited by 18 publications

(2 citation statements)

References 23 publications

(34 reference statements)

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Another solution may be given by the use of doping the spinel structure with some foreign cations, such as Al, which makes a tremendous change in ferrite behavior [14]. Many papers used ferrite as a support for the TiO 2 photo catalyst [15][16][17][18][19][20]. In these papers, the adding of the Ti precursors on already prepared ferrite materials is performed.…”

Section: Introductionmentioning

confidence: 99%

Surface Modification of Zinc Ferrite with Titanium to Be a Photo-Active Catalyst in Commercial LED Light

Baamer,

Abd El Maksod

2023

Catalysts

View full text Add to dashboard Cite

Titanium-doped zinc ferrite was used as a photo catalyst for breaking down C-C and C-H bonds of methylene blue dye as a model for the decomposition of organic pollutants. Different concentrations of Ti were used to impede into the spinel structure of zinc ferrite by in situ addition during the preparation. Different characterization techniques were used to characterize the prepared materials including the deep analysis of the electronic spectra, which proved the surface modification of ferrite due to the Ti doping. In addition, we make a comparison study of photo degradation using ordinary UV irradiation and commercial LED light irradiation, which gives very promising results. A correlation between the structure and the photo catalytic behavior of the materials is assigned.

show abstract

Section: Introductionmentioning

confidence: 99%

Surface Modification of Zinc Ferrite with Titanium to Be a Photo-Active Catalyst in Commercial LED Light

Baamer,

Abd El Maksod

2023

Catalysts

View full text Add to dashboard Cite

show abstract

“…Meanwhile, nanoparticles may improve the material properties and exhibit more excellent characteristics than bulk materials. Therefore, preparing superfine Co 2 O 3 nanoparticles and studying the properties of the resulting particles are very important to determine their potential industrial application [4][5][6].…”

Section: Introductionmentioning

confidence: 99%

Effect of Synthetic Technology on the Properties of Co<sub>2</sub>O<sub>3</sub> Powder

Xiong

Sun

Yang

et al. 2018

SSP

View full text Add to dashboard Cite

Ultrafine Co2O3powder was prepared via hydrothermal synthesis. The effect of technology on the performance of the superfine Co2O3powders was investigated, and the hydrothermal parameters in preparing Co2O3were gradually improved. In addition, the morphology and grain size of the Co2O3powder were analyzed by FESEM. Results show that reducing the salt–alkali molar ratio resulted in more uniform Co2O3powder and smaller particles, with average particle size of approximately 40 nm. Reaction time displayed little effect on the Co2O3powder, but the particle size decreased with the reaction time. The concentration of salt solution remarkably affected the morphology of the Co2O3powder. Lower concentration resulted in smaller particle aggregation and particle size.

show abstract

Synthesis of Co-substituted Mn-Zn ferrite nanoparticles by mechanochemistry approach

et al. 2016

View full text Add to dashboard Cite

Effects of TiO2 and Co2O3 combination additions on the elemental distribution and electromagnetic properties of Mn–Zn power ferrites

Cited by 18 publications

References 23 publications

Surface Modification of Zinc Ferrite with Titanium to Be a Photo-Active Catalyst in Commercial LED Light

Surface Modification of Zinc Ferrite with Titanium to Be a Photo-Active Catalyst in Commercial LED Light

Effect of Synthetic Technology on the Properties of Co<sub>2</sub>O<sub>3</sub> Powder

Synthesis of Co-substituted Mn-Zn ferrite nanoparticles by mechanochemistry approach

Contact Info

Product

Resources

About