Effects of thermal annealing on the viscoelastic properties and morphology of bimodal hard/soft latex blends

Abstract

The effects of thermal annealing on the viscoelastic properties and morphology of films prepared from bimodal latex blends containing equal weight fractions of soft and hard latex particles with controlled sizes were investigated. The thermal and viscoelastic properties of as‐dried and annealed samples were investigated with differential scanning calorimetry and dynamic mechanical analysis (DMA). Throughout the thermal annealing, the latex blend morphologies were also followed with atomic force microscopy and transmission electron microscopy (TEM). A particulate morphology, consisting of hard particles evenly dispersed in a continuous soft phase, was observed in the TEM micrographs of the as‐dried latex blends and resulted in an enhancement of the mechanical film properties at temperatures between the α relaxations of the soft and hard phases in the DMA thermograms. As soon as the thermal annealing involved temperatures higher than the glass‐transition temperature of the hard phase, the hard particles progressively lost their initial spherical shape and formed a more or less continuous phase in the latex blends. This induced coalescence of the hard particles was confirmed by the association of the experimental viscoelastic data with theoretical predictions, based on self‐consistent mechanical models, which were performed by the consideration of either a particulate or cocontinuous morphology for the bimodal latex blends. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2289–2306, 2005

Waterborne acrylic–casein latexes as eco-friendly binders for coatings

“…Other alternative to solve this issue is to introduce a harder phase to a soft binder that will bloom to the top of a film as it dries. Typically, solutions involve the use of blends of hard/soft latex particles [7][8][9][10][11][12][13][14][15][16] or surface-active agents as silicon-based materials, waxes and/or fluorinated additives. In this scenery, the use of a natural compound with a high T g (∼180 • C), as casein, in combination with a soft acrylic polymer appears as a promising system to produce waterborne nanostructured binders that simultaneously attain these antagonistic requirements.…”

New waterborne acrylic binders for zero VOC paints

“…4: Tan d as a function of temperature for four polymer blend samples (see Table 3). The samples distinguish themselves by the amount of hard polymer (i.e., hard/soft ratio): (a) 10% hard polymer, (b) 12.5% hard polymer, (c) 15% hard polymer, (d) 16.5% hard polymer a All application properties were obtained with a standard paint formulation with a PVC (pigment volume concentration) of 20% b,c Interaction and stability were judged by examination of the fracture surface using SEM (see Fig. 3) c The methods are described in Table 1 Defoamer Tego 0.9 a As described in Table 5 a All application properties were obtained with a standard paint formulation with a PVC (pigment volume concentration) of 20% b,c Interaction and stability were judged by examination of the fracture surface using SEM (see Fig.…”

“…DMTA is a powerful technique for the study of blends of polymers. 15,16 Although only a relatively small amount of hard polymer was incorporated, this hard polymer seemed to dominate completely the mechanical properties of the film. In this specific case when only 16.5 wt% of hard polymer was added, the loss tangent tan d (E¢¢/E¢) showed the dominant presence of hard polymer.…”

Effect of annealing on self-organized gradient film obtained from poly(3-[tris(trimethylsilyloxy)silyl] propyl methacrylate-co-methyl methacrylate)/poly(methyl methacrylate-co-n-butyl acrylate) blend latexes

“…The surface morphology evolution and phase separation of the polymeric film can be induced by temperature [33][34][35][36][37][38]. Herein, our 1:1 blend films were annealed at 80 (Fig.…”