Effects of strain localization on surface roughening during sheet forming

Becker, Richard

doi:10.1016/s1359-6454(97)00182-1

Cited by 189 publications

(110 citation statements)

References 15 publications

Supporting

Mentioning

101

Contrasting

Unclassified

Order By: Relevance

“…Some studies of deformation of polycrystals show that the surface roughness increases with plastic strain (Becker, 1998 andYue, 2005). Under fatigue loading, it was found that the surface roughness increased with fatigue life, and the deformation is localized in some specific places, where micro-cracks are nucleated (Yue, 2005 ).…”

Section: Introductionmentioning

confidence: 99%

Influence of machining parameters on fatigue endurance limit of AISI 4140 steel

Lopes¹,

Sales²,

Palma³

2008

J. Braz. Soc. Mech. Sci. & Eng.

View full text Add to dashboard Cite

show abstract

Section: Introductionmentioning

confidence: 99%

Influence of machining parameters on fatigue endurance limit of AISI 4140 steel

Lopes¹,

Sales²,

Palma³

2008

J. Braz. Soc. Mech. Sci. & Eng.

View full text Add to dashboard Cite

show abstract

“…Since rough surfaces require more effort for polishing and/or painting after forming processes, deformation induced surface roughening of metallic sheets has been widely examined. [4][5][6][7][8][9][10] In the present study deformation induced surface roughening behavior of two austenitic stainless steel sheets was compared. These steel sheets had been imported from two different countries by a Turkish firm for production of cups and other kitchenware by sheet metal forming processes.…”

Section: Introductionmentioning

confidence: 99%

Deformation Induced Surface Roughening of Austenitic Stainless Steels

et al. 2003

View full text Add to dashboard Cite

“…where L represents the length of surface asperity after a certain deformation, and  is the distance from this line to the surface nodes [1,18]. There is an obvious tendency that, with an increase of gauged reduction, the surface asperity (surface roughness) tends to be flattened.…”

Section: Analysis Of Surface Roughness and Hardnessmentioning

confidence: 99%

Microtexture based analysis of surface asperity flattening behavior of annealed aluminum alloy in uniaxial planar compression

Jiang

Wei

et al. 2013

Tribology International

View full text Add to dashboard Cite

X. (2013). Microtexture based analysis of surface asperity flattening behavior of annealed aluminum alloy in uniaxial planar compression. Tribology International, Microtexture based analysis of surface asperity flattening behavior of annealed aluminum alloy in uniaxial planar compression AbstractDuring the uniaxial planar compression of annealed aluminum alloy, a novel approach to determine surface asperity flattening (roughness Ra) is employed by analyzing the evolution of surface microtexture. With an increase in gauged reduction, surface asperity tends to be flattened, and strain hardening increases. Lubrication can constrain the surface asperity flattening process. Development of surface asperity features shows the obvious dependency on [111] orientation. In-grain slips contribute significantly to the evolution of surface microtexture. Influence of deformation twins (brass orientation) on the evolution of microtexture is not obvious under our current experimental conditions. on the evolution of microtexture is not obvious under our current experimental conditions.

show abstract

Effects of strain localization on surface roughening during sheet forming

Cited by 189 publications

References 15 publications

Influence of machining parameters on fatigue endurance limit of AISI 4140 steel

Influence of machining parameters on fatigue endurance limit of AISI 4140 steel

Deformation Induced Surface Roughening of Austenitic Stainless Steels

Microtexture based analysis of surface asperity flattening behavior of annealed aluminum alloy in uniaxial planar compression

Contact Info

Product

Resources

About