Effects of organic acids on the performance of cellulose triacetate forward osmosis membrane

Thermally responsive polymers (TRPs) have gained significant attention in the past decade due to their unique phase transition behavior, those exhibiting changes in properties with temperature variations. In water, hydrophilic block copolymers form helical structures that can transform into hydrophobic globules above the lower critical solution temperature (LCST). Fouling is one of the limiting issues for the forward osmosis (FO) process in wastewater treatment. In this work, after the treatment of wastewater from the paper and pulp industries, foulants were removed from the surface of the commercial polyamide thin‐film composite membrane of the FO process using polyvinyl methyl ether (PVME), a TRP with an LCST of 35–37°C. PVME was mixed with different aqueous solutions to form cleaning solutions. Foulant cleaning experiments utilized a 1% PVME (w/v) solution in 300 mL of de‐ionized (DI) water, while 1 M NaCl solution served as the draw solution (DS) in the FO process. Comparing the water flux (J) and change in membrane hydraulic resistance (Rf) among pristine, fouled, and cleaned membranes revealed a 56.67% increase in water flux and a 51.68% decrease in membrane resistance after PVME mixed with DI water cleaning solution showcasing its effectiveness in improving membrane performance and reducing fouling. The cleaning efficiency of two solutions, that is, 1% PVME mixed in DI water and 1% PVME mixed in 1 M aqueous urea solution, is compared. Results showed that the former cleaning solution helped to obtain 32.62% higher water flux and 56.05% less membrane resistance. Various membrane characterizations are performed, such as field emission scanning electron microscopy (FE‐SEM), which characterizes the membrane's pore structure and surface morphology, while a contact angle analyzer assesses hydrophilicity. This research highlights the use of TRPs as effective cleaning agents, enhancing membrane performance by effectively removing foulants on the membrane surface. Investigating alternative cleaning solutions also provides insights for optimizing water treatment processes.Highlights Cleaning of fouled thin‐film composite membrane using thermal‐responsive polymers (TRPs). Polyvinyl methyl ether, a TRP with an lower critical solution temperature of 35–37°C used as a cleaning agent. 60% increase in water flux was observed after the single‐step cleaning process. Multiple uses of TRP for cleaning performed with no membrane damage.

Section: Introductionmentioning

confidence: 99%

Section: Introductionmentioning

confidence: 99%

Thermo‐responsive polymer to clean fouled forward osmosis membrane after wastewater treatment: Excellent flux recovery

Rai,

Pandey,

Singh

et al. 2024

“…CA membranes are produced from the acetylation of cellulose to obtain cellulose triacetate (CTA) and cellulose diacetate acetate by acetic anhydride. [ 10‐15 ] Cellulose is a natural product, asymmetric polymer (crystalline and amorphous). It could extract from natural products of agricultural like fiber.…”

Section: Introductionmentioning

confidence: 99%

Effect of cellulose acetate/cellulose triacetate ratio on reverse osmosis blend membrane performance

Elkony

Mansour

Elhusseiny

et al. 2020

Surface functionalization and modification including the grafting process are effective approaches to improve and enhance the reverse osmosis (RO) membrane performance. This work is aimed to synthesize grafted/crosslinked cellulose acetate (CA)/cellulose triacetate (CTA) blend RO membranes using N‐isopropylacrylamide (N‐IPAAm) as a monomer and N,N‐methylene bisacrylamide (MBAAm) as a crosslinker. The morphology of these membranes was analyzed by scanning electron microscopy and their surface roughness was characterized by atomic force microscopy. The performance of these membranes was evaluated through measuring two major parameters of salt rejection and water flux using RO unit at variable operating pressures. It was noted that the surface average roughness obviously decreased from 148 nm for the pure CA/CTA blend membrane with 2.5% CTA to 110 nm and 87 nm for the grafted N‐IPAAm and grafted/crosslinked N‐IPAAM/MBAAm/CA/CTA‐RO membranes, respectively. Moreover, the contact angle decreased from 51.98° to 47.6° and 43.8° after the grafting and crosslinking process. The salt rejection of the grafted CA/CTA‐RO membrane by 0.1% N‐IPAAm produced the highest value of 98.12% and the water flux was 3.29 L/m2h at 10 bar.

Synthesis and characterization of PES/PSF/PEG by immersion precipitation for Mediterranean seawater desalination by FO membrane

Hassen

Hamdy

Sabry

et al. 2022

In the present study, a simple, inexpensive, nontoxic, and environmentally friendly polyethylene glycol (PEG) polymer was used to enhance the hydrophilicity of the forward osmosis (FO) membrane using various PEG concentrations as a pore forming agent in the casting solution of polyethersulfone/polysulfone (PES/PSF) blend membranes. A nonwoven PES/PSF FO blend membrane was fabricated via the immersion precipitation phase inversion technique. The membrane dope solution was cast on polyethylene terephthalate (PET) nonwoven fabric. The results revealed that PEG is a pore forming agent and that adding PEG promotes membrane hydrophilicity. The membrane with 1 wt% PEG (PEG1) had about 27% lower contact angle than the pristine blend membrane. The PEG1 membrane has less tortuosity (which reduces from 3.4–2.73), resulting in a smaller structure parameter (S value) of 277 μm, due to the presence of open pores on the bottom surface structure, which results in diminished ICP. Using 1 M NaCl as the draw solution and distilled water as the feed solution, the PEG1 membrane exhibited higher water flux (136 L m−2 h−1) and lower reverse salt flux (1.94 g m−2 h−1). Also, the selectivity of the membrane, specific reverse salt flux, (Js/Jw) showed lower values (0.014 g/L). Actually, the PEG1 membrane has a 34.6% higher water flux than the commercial nonwoven‐cellulose triacetate (NW‐CTA) membrane. By means of varied concentrations of NaCl salt solution (0.6, 1, 1.5, and 2 M), the membrane with 1 wt% PEG showed improved FO separation performance with permeate water fluxes of 108, 136, 142, and 163 L m−2 h−1. In this work, we extend a promising gate for designing fast water flux PES/PSF/PEG FO blend membranes for water desalination.