Effect of the Alumina Shell on the Melting Temperature Depression for Aluminum Nanoparticles

Abstract

The dependence of aluminum (Al) melting temperature on particle size was studied using a differential scanning calorimeter and thermogravitmetric analyzer for particles encapsulated in an oxide shell. Pressure generation within the Al core leads to an increase in melting temperature in comparison with traditional melting temperature depression calculated using the Gibbs−Thomson equation. On the basis of elasticity theory, the pressure in the Al core at the onset of melting is caused mainly by surface tension at the alumina−air and Al−alumina interfaces. This implies that pressure due to the difference in thermal expansion of aluminum and alumina relaxes. A possible relaxation mechanism is discussed. The static strength of the alumina shell and the maximum static generated pressure in aluminum were evaluated. Mechanically damaging the oxide shell was shown to reduce the melting temperature due to a decrease in generated pressure within the Al core. Thus, reduction in melting temperature can be used as a quantitative measure of damage to the oxide shell. Results from X-ray diffraction studies show that 17-nm diameter Al particles had a 2-nm thick alumina shell in the γ-phase, while for a flat surface Al had an amorphous alumina shell stable to a thickness of 4 nm. Thus, pressure due to surface tension promotes denser γ-phases. Since particles with shells initially in the amorphous or γ-phase show the same flame speed and ignition delay time, fast oxidation observed under high heating rates cannot be explained by a phase transformation in the alumina shell. These findings have important implications for the melt-dispersion mechanism for fast Al oxidation. The dependence of aluminum (Al) melting temperature on particle size was studied using a differential scanning calorimeter and thermogravitmetric analyzer for particles encapsulated in an oxide shell. Pressure generation within the Al core leads to an increase in melting temperature in comparison with traditional melting temperature depression calculated using the Gibbs-Thomson equation. On the basis of elasticity theory, the pressure in the Al core at the onset of melting is caused mainly by surface tension at the alumina-air and Al-alumina interfaces. This implies that pressure due to the difference in thermal expansion of aluminum and alumina relaxes. A possible relaxation mechanism is discussed. The static strength of the alumina shell and the maximum static generated pressure in aluminum were evaluated. Mechanically damaging the oxide shell was shown to reduce the melting temperature due to a decrease in generated pressure within the Al core. Thus, reduction in melting temperature can be used as a quantitative measure of damage to the oxide shell. Results from X-ray diffraction studies show that 17-nm diameter Al particles had a 2-nm thick alumina shell in the γ-phase, while for a flat surface Al had an amorphous alumina shell stable to a thickness of 4 nm. Thus, pressure due to surface tension promotes denser γ-phases. Since particles with shells in...

Size and mechanics effects in surface-induced melting of nanoparticles

“…They include surface premelting and melting below the thermodynamic melting temperature θ e , caused by reduction in surface energy and leading to appearance of a molten, nanometer-thick layer 1,2 ; reduction in melting temperature θ m with reduction of the particle radius R down to nanoscale 3,4 ; melting of particles with radii comparable to and smaller than the equilibrium solid-liquid interface width δ e , which is a few nm 3,5 ; and overheating above θ e during very fast heating 6,7 . All of these phenomena allow one to determine the properties of solid and liquid deeply in the region of their metastability and even complete instability (that is, above the solid instability temperature θ i or below the melt instability temperature θ c , see Supplementary Fig.…”

Physical and mathematical model of detonation in aluminum gas suspensions with regard for transition processes of nanosized particle flow, heat transfer and combustion

“…This criterion was substantiated in [27] when considering the ignition of aluminum particles in a shock wave, taking into account surface oxidation reactions and polymorphic transformations of the oxide. According to numerous experimental ignition data [15], the ignition threshold remains at about 900 K. The theoretical explanation of the rapid ignition of nanoscale particles due to the sharp disintegration of the particle core during melting is given in Refs [28,16]. Thus, for particles of size 50 ÷ 250 nm, we consider the ignition temperature equal to the melting point…”

Stress relaxation in pre-stressed aluminum core–shell particles: X-ray diffraction study, modeling, and improved reactivity

“…The obtained experimental and theoretical results represent important progress in our main objective of designing optimal Al micron-scale particles for energy-related applications. Also, this new model for stress relaxation in an alumina shell can be used for improving the model for melting of Al particles covered by an alumina shell [21] and interpreting of experimental data.…”