Effect of silicon and titanium on the microstructure and mechanical properties of ZA12 alloy

Liu, Saisai; Tu, Hao; Wu, Changjun; Wang, Jianhua; Su, Xuping

doi:10.1016/j.mtcomm.2021.102564

Search citation statements

Order By: Relevance

Paper Sections

Select...

Introduction Giriş1

Citation Types

Supporting

Mentioning

Contrasting

Year Published

2022

2024

Publication Types

Select...

Article4

Relationship

Self Cite0

Independent4

Authors

Journals

Cited by 4 publications

(1 citation statement)

References 15 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The increase in the strength of the Zn-Al based alloy with the presence of these alloying elements is mainly due to solid solution hardening and the formation of new phases. Liu et al (2021) reported that the hardness of the Zn-12Al based alloy increased with the addition of Si increasing up to 1.2 wt. % due to silicon particles being harder than the matrix, but that when the Si content exceeded 0.3 wt.…”

Section: Introduction Girişmentioning

confidence: 99%

Investigation of microstructural change and damping behaviour of Zn–27Al–1Cu alloy in different aging periods

Şenaslan¹,

Aydın²

2022

Gümüşhane Üniversitesi Fen Bilimleri Enstitüsü Dergisi

View full text Add to dashboard Cite

show abstract

Section: Introduction Girişmentioning

confidence: 99%

Investigation of microstructural change and damping behaviour of Zn–27Al–1Cu alloy in different aging periods

Şenaslan¹,

Aydın²

2022

Gümüşhane Üniversitesi Fen Bilimleri Enstitüsü Dergisi

View full text Add to dashboard Cite

show abstract

Effect of Isothermal Treatment on Mechanical and Tribological Properties of Alloy Zn – 40% Al – 2% Cu – 2% Si

Savaşkan,

Hekimoğlu,

Azaklı

2023

Met Sci Heat Treat

View full text Add to dashboard Cite

Lubricated Wear Properties of Zn-30Al-3Cu-Si Alloys

Savaşkan,

Tan

2024

JOM

View full text Add to dashboard Cite

To assess the effect of silicon content (SC) and test parameters on the lubricated wear of Zn-30 wt.% Al-3 wt.% Cu-(0.5–5) wt.% Si alloys, six quaternary alloys were produced by casting. Their wear properties were investigated at different ranges of contact pressure (CP) of 1–8 MPa and sliding velocity (SV) of 1–3 ms−1 for two different sliding distances (SD) of 20 km and 108 km. It was observed that Si addition (SA) improved the tribological properties of Zn-30Al-3Cu alloy, but an increase in the SC above a certain percentage (0.5%) adversely affected these properties. Therefore, Zn-30Al-3Cu-0.5Si alloy demonstrated the lowest friction coefficient (FC) and wear volume (WV) among the alloys tested. The correlations between the lubricated wear properties (FC and WV) of the alloys and test conditions (CP and SV) were made by non-linear regression analysis using the wear test data. Finally, the equations for the relationship between the wear properties of the alloys and the test parameters were determined.

show abstract

Effect of silicon and titanium on the microstructure and mechanical properties of ZA12 alloy

Cited by 4 publications

References 15 publications

Investigation of microstructural change and damping behaviour of Zn–27Al–1Cu alloy in different aging periods

Investigation of microstructural change and damping behaviour of Zn–27Al–1Cu alloy in different aging periods

Effect of Isothermal Treatment on Mechanical and Tribological Properties of Alloy Zn – 40% Al – 2% Cu – 2% Si

Lubricated Wear Properties of Zn-30Al-3Cu-Si Alloys

Contact Info

Product

Resources

About