Effect of Shot Peening Strengths on Microstructure and Mechanical Properties of 316L Stainless Steel Prepared by 3D Printing

Pan, Haijun; Tao, Wenyu; Zhang, Bin; Jiang, Peng; Wang, Zhizhi; Wu, Wangping; Liu, Lin; Li, Jing; Wu, Zhiqiang; Cai, Zhiping

doi:10.1002/adem.202201675

Cited by 8 publications

(1 citation statement)

References 29 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The incremental hardness was often linked to a shrinkage in grain size, as indicated by the Hall-Petch formula. In the context, researchers like Pan et al [45,46] suggest that SP can enhance the hardness of materials such as 316L stainless steel, primarily through mechanisms like refinement hardening, dislocation hardening, and straininduced martensite formation. In the range of SP parameters examined in this experiment, both surface hardness and the degree of hardness increase for LSMSPed gears show an upward trend.…”

Section: Microhardnessmentioning

confidence: 99%

The effect of shot peening on the contact fatigue performance of C40 steel gears after laser surface melting

Lv,

Cui,

Sun

et al. 2024

Surf. Topogr.: Metrol. Prop.

View full text Add to dashboard Cite

In this paper, shot peening (SP) was employed as a post-processing technique for the laser surface melted (LSMed) gear. The aim was to improve the contact fatigue performance of laser surface melting+shot peened (LSMSPed) gears. The microstructure, surface roughness, residual stress, microhardness of C40 steel gears before and after SP treatment were characterized using scanning electron microscopy, X-ray diffraction stress analyzer, contour measuring instrument, and hardness tester. Fatigue test of gear was carried out with a Forschungsstelle für Zahnräder und Getriebebau (FZG) testing machine. Following the laser surface melting (LSM) treatment, a molten layer was observed on the gear teeth surface. The experimental results indicated that SP induced a hardened layer with a certain thickness and plastic deformation on the surface of LSMed gears. Importantly, as the SP parameters increased, there's a corresponding reduction in both the average grain diameter and the maximum grain diameter. The reduction was most pronounced when the shot diameter reached its maximum value. It's worth noting that once the optimal threshold for SP parameters is surpassed, the residual compressive stress and microhardness on the LSMSPed gear surface do not exhibit a continuous growth trend. Furthermore, the rise in SP parameters resulted in a gradual increase in the surface roughness of LSMSPed gears, albeit to varying degrees. In light of the combined effects of grain refinement, residual compressive stress, microhardness, and surface roughness, the contact fatigue performance of LSMSPed gears improved with increasing SP parameters. Notably, when comparing the contact fatigue life of LSMed gears with that of LSMSPed gears, we observed a substantial enhancement. However, it's essential to highlight that when the shot diameter reaches its maximum value, the contact fatigue life of the LSMSPed gear, somewhat unexpectedly, decreased.

show abstract

Section: Microhardnessmentioning

confidence: 99%

The effect of shot peening on the contact fatigue performance of C40 steel gears after laser surface melting

Lv,

Cui,

Sun

et al. 2024

Surf. Topogr.: Metrol. Prop.

View full text Add to dashboard Cite

show abstract

Achieving Excellent Strength–Ductility Combination by Austempering below Ms in 40CrNiMo Steels

et al. 2023

Self Cite

View full text Add to dashboard Cite

Herein, the microstructure evolution and mechanical properties of the 40CrNiMo steel treated by different austempering temperatures are investigated. With the decrease in austempering temperatures from 270 to 180 °C, the volume fraction of bainite decreases, and the martensite fraction increases. The austenite content is about 8% at 270 °C, and then increases over 12% at 240≈180 °C. The mean grain size decreases from 270 to 180 °C, which is related to the reason that the development of bainite/austenite interface is restricted for the martensite formation. The yield strength increases from 1153 to 1323 MPa by refinement hardening and dislocation hardening, and ultimate tensile strength increases from 1193 to 1731 MPa at from 270 to 180 °C. The elongation is about 13% at 210≈270 °C, and then decreases at 180 °C.

show abstract

Effect of Shot Peening on Microstructure and Mechanical Properties of 316L Stainless Steel Prepared by 3D Printing with Different Forming Angles

Pan,

Wang,

Zhang

et al. 2023

J. of Materi Eng and Perform

View full text Add to dashboard Cite

Effect of Shot Peening Strengths on Microstructure and Mechanical Properties of 316L Stainless Steel Prepared by 3D Printing

Cited by 8 publications

References 29 publications

The effect of shot peening on the contact fatigue performance of C40 steel gears after laser surface melting

The effect of shot peening on the contact fatigue performance of C40 steel gears after laser surface melting

Achieving Excellent Strength–Ductility Combination by Austempering below Ms in 40CrNiMo Steels

Effect of Shot Peening on Microstructure and Mechanical Properties of 316L Stainless Steel Prepared by 3D Printing with Different Forming Angles

Contact Info

Product

Resources

About