Effect of milled glass fiber on fatigue life of basalt fiber reinforced composites

Dheepthi, M.; T., None Sivagangai; Radhakrishnan, P.M.; Santhanakrishnan, R.

doi:10.1016/j.matpr.2023.01.228

Cited by 5 publications

(1 citation statement)

References 10 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…These composites exhibit a tendency to fracture easily, which significantly restricts their utilization in scenarios necessitating flexibility. To address this limitation, researchers [28][29][30] have focused their efforts on investigating methods to enhance the toughness of these composites through the integration of supplementary materials like carbon nanotubes or the exploration of alternative polymer matrices.…”

Section: Introductionmentioning

confidence: 99%

Development and Mechanical Properties Evaluation of Basalt-Glass Hybrid Composites

M. Prasanna Kumar,

Vinay K M

2023

Evergreen

View full text Add to dashboard Cite

In this study, the mechanical properties of hybrid composites reinforced with both Basalt fibers and Glass fibers are evaluated. The composites were fabricated through the use of a hand layup process followed by compression molding techniques. The composites in this study were prepared using traditional hand layup technique, with Lapox L-12 and K-6 epoxy serving as the matrix. Different fiber stacking sequences and thicknesses were used in the fabrication process. The mechanical properties of the composites and hybrid composites, such as flexural strength, impact strength, and tensile strength, were determined. The measurements were taken in accordance with ASTM standards. The results indicate that the addition of basalt and glass fibers as reinforcements has a substantial impact on the mechanical properties of the composites. It was found that the composites reinforced with basalt-glass fibers possess superior mechanical properties when compared to those reinforced with basalt and glass fibers alone.

show abstract

Section: Introductionmentioning

confidence: 99%

Development and Mechanical Properties Evaluation of Basalt-Glass Hybrid Composites

M. Prasanna Kumar,

Vinay K M

2023

Evergreen

View full text Add to dashboard Cite

show abstract

Comparative evaluation of solid particle erosion resistance in milled carbon fiber‐reinforced basalt fiber epoxy composites: Impact of abrasive shape variations

Ürgün,

Özsoy,

Bora

et al. 2024

Polymer Composites

View full text Add to dashboard Cite

The solid particle erosive wear performance of basalt fiber‐reinforced epoxy composites with the incorporation of different percentages of milled carbon fiber fillers (0–10 wt%) is evaluated under various abrasive materials (garnet and ceramic beads) and impingement angles (30° and 90°). Erosion tests have been carried out following ASTM G76 standards using a factorial design method. The data indicate that the erosion rates, crater depths, and areas of craters are all strongly dependent on erodent material type and milled carbon fiber filler ratio. Compared to ceramic beads, garnet abrasives caused severe erosion, with erosion rates reaching approximately 500 mg/g at a 90° impingement angle without milled carbon fiber fillers. Erosion by both abrasives was significantly reduced by the introduction of milled carbon fiber fillers into the basalt fiber composites, with the erosion rate decreasing to around 100 mg/g with 3 wt% milled carbon fiber fillers. The maximum crater depth was also influenced; garnet abrasives produced craters as deep as 1000 μm without fillers at 90°, which was reduced to 451 μm with 3 wt% milled carbon fiber fillers when ceramic beads were used. Of the three factors for the erosion rate and crater depth, inorganic erodent material and ratio of carbon fiber filler were prominent, but the impingement angle effect was much smaller. Among the three factors for the erosion rate and crater depth, erodent material and carbon fiber filler ratio were prominent, while the impingement angle effect was significantly less.Highlights The garnet abrasives cause more severe erosion than ceramic beads at 90°. Composites exhibit optimal erosion resistance with 3–5 wt% milled carbon fiber fillers. Filler ratio and erodent material type significantly impact erosion rates and depths. Factors affecting wear performance identified using factorial design and ANOVA.

show abstract

Effect of stress level on creep-fatigue interaction of woven angle ply GFRP laminates

Radhakrishnan

Ramajeyathilagam

2023

Materials Today: Proceedings

View full text Add to dashboard Cite

Effect of milled glass fiber on fatigue life of basalt fiber reinforced composites

Cited by 5 publications

References 10 publications

Development and Mechanical Properties Evaluation of Basalt-Glass Hybrid Composites

Development and Mechanical Properties Evaluation of Basalt-Glass Hybrid Composites

Comparative evaluation of solid particle erosion resistance in milled carbon fiber‐reinforced basalt fiber epoxy composites: Impact of abrasive shape variations

Effect of stress level on creep-fatigue interaction of woven angle ply GFRP laminates

Contact Info

Product

Resources

About