“…Previous studies have shown that the CTE of Al-Si multicomponent casting alloys was influenced by several factors, such as the morphology of the secondary phases, [12][13][14][15][16][17] different alloy elements, [18][19][20] different technical processes [21][22][23][24] and the magnitude and distribution of internal stresses produced at the interfaces. 25,26 In addition, the thermal history 21,27 as and porosity 28 also have significant effects on the thermal expansion behaviour.…”
Al-Si casting alloys are the most commonly used materials for piston alloys. The coefficient of thermal expansion is the key property of a piston material for improving the overall performance and service life of an engine. In the present study, the relationship between the morphology of the excess silicon phase and the coefficient of thermal expansion of Al-Si binary casting alloys was discussed. Optical and scanning electron microscopy were utilized to observe the morphology of the excess silicon phase in the Al-Si binary casting alloys before and after solution aging treatment. The results showed that the morphology of the excess silicon phase significantly influenced the coefficient of thermal expansion of the Al-Si binary casting alloys. After solution aging treatment, the coefficient of thermal expansion of the Al-Si binary casting alloys increased due to the rounding and granulating of the excess silicon phase precipitated during the casting process and decreased due to the precipitation of the finely dispersed Si phase in the α-Al matrix. The change in the coefficient of thermal expansion depended on which of the two kinds of morphological transformation of the excess silicon phase is dominant.
“…Previous studies have shown that the CTE of Al-Si multicomponent casting alloys was influenced by several factors, such as the morphology of the secondary phases, [12][13][14][15][16][17] different alloy elements, [18][19][20] different technical processes [21][22][23][24] and the magnitude and distribution of internal stresses produced at the interfaces. 25,26 In addition, the thermal history 21,27 as and porosity 28 also have significant effects on the thermal expansion behaviour.…”
Al-Si casting alloys are the most commonly used materials for piston alloys. The coefficient of thermal expansion is the key property of a piston material for improving the overall performance and service life of an engine. In the present study, the relationship between the morphology of the excess silicon phase and the coefficient of thermal expansion of Al-Si binary casting alloys was discussed. Optical and scanning electron microscopy were utilized to observe the morphology of the excess silicon phase in the Al-Si binary casting alloys before and after solution aging treatment. The results showed that the morphology of the excess silicon phase significantly influenced the coefficient of thermal expansion of the Al-Si binary casting alloys. After solution aging treatment, the coefficient of thermal expansion of the Al-Si binary casting alloys increased due to the rounding and granulating of the excess silicon phase precipitated during the casting process and decreased due to the precipitation of the finely dispersed Si phase in the α-Al matrix. The change in the coefficient of thermal expansion depended on which of the two kinds of morphological transformation of the excess silicon phase is dominant.
“…В работе [12] показан способ получения композитного материала системы Al-Al 2 O 3 методом пластической деформации, а в [13] описан способ получения ДУКМ, насыщенного частицами нитрида алюминия по реакции Al 2 O 3 + + 3C + N 2 → 2AlN + 3CO. В работе [14] предложен способ получения керамического композита Al 2 O 3 -AlON-AlN, в [15] рассмотрен процесс продувки алюминиевого расплава водяным паром с получением легких деформируемых высококремнистых сплавов многоцелевого назначения, в [16] описан способ получения композита Al-TiC путем синтеза карбида титана непосредственно в расплаве Al-Ti с вводом в него углеводородсодержащего газа, развиваются и другие технологии.…”
Нижегородский государственный технический университет им. Р.Е. Алексеева (НГТУ) Нижегородский государственный архитектурно-строительный университет (НГАСУ) Статья поступила в редакцию 12.10.16 г., доработана 16.03.17 г., подписана в печать 20.03.17 г. В настоящее время ответственные детали и узлы, изготовленные из традиционных материалов, не всегда удовлетворяют возросшим требованиям конструкторов и условиям эксплуатации. Одним из решений данной проблемы являются разработка и применение дисперсно-упрочненных композиционных материалов с металлической матрицей. В работе на основе информационно-аналитического обзора предложена новая технология создания дисперсно-упроченного композиционного материала на основе алюминия. Изложены особенности разрабатываемой технологии, приведены макро-и микроструктуры и механические характеристики образцов в литом состоянии. Синтез упрочняющих частиц непосредственно в расплаве позволяет получать композиты в одну стадию и обеспечивать термодинамическую устойчивость, плотный контакт и хорошую адгезию между матрицей и упрочняющей фазой. Достигнутые размеры частиц твердой фазы внедрения находятся в пределах от 3 мкм до 2 мм. Изучение структурно-фазового состояния полученного материала проводили с использованием методов оптической металлографии и рентгеноструктурного анализа (дифрактомер «Дрон-2»). Микроструктуру исследовали на микроскопе «Keyence VHX-1000». Твердость образцов определяли на ТКС-1М, микротвердость-на ПМТ-3 и «HMV Shumadzu», предел прочности-на универсальных разрывных машинах ZD 10/90 и УМЭ-10ТМ, ударную вязкость-на маятниковом копре МК-30а. Установлено что варьирование размера и содержания упрочняющей фазы позволяет изменять механические свойства литого металла в широких пределах. Применение предлагаемой технологии позволит существенно снизить временные и экономические затраты. По результатам оценочного расчета ожидается уменьшение стоимости получения дисперсно-упрочненного композиционного материала. Ключевые слова: дисперсно-упрочненный материал, металломатричный композитный материал, алюминий, оксид алюминия, мелкодисперсная тугоплавкая частица, упрочняющая фаза, технология, свойства, структура.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.