Effect of gamma irradiation on stress corrosion behavior of austenitic stainless steel under ITER-relevant conditions

Jones, R.H.; Henager, Charles H.

doi:10.1016/0022-3115(92)90627-w

Cited by 4 publications

(2 citation statements)

References 3 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The researchers found that solutes such as Fe +2 and Cl-ions can alter the magnitude of radiation effect by reacting preferentially with specific radiolysis products thereby changing their relative concentrations. Other researchers [9,15,[28][29][30][31][32][33][34][35][36][37][38][39][40][41][42][43][44][45] found that intergranular stress corrosion cracking IGSCC and irradiation assisted stress corrosion cracking IASCC in radiated austenitic alloys can be observed. However, others showed that the exact mechanism is still not fully understood [33,34,[46][47][48][49][50][51].…”

Section: Discussionmentioning

confidence: 99%

Characterization of gamma-ray irradiation influence on the corrosion behaviour of austenitic stainless steel

Aljohani

Geesi

Kaïba

et al. 2020

Materials Today Communications

View full text Add to dashboard Cite

This is a PDF file of an article that has undergone enhancements after acceptance, such as the addition of a cover page and metadata, and formatting for readability, but it is not yet the definitive version of record. This version will undergo additional copyediting, typesetting and review before it is published in its final form, but we are providing this version to give early visibility of the article. Please note that, during the production process, errors may be discovered which could affect the content, and all legal disclaimers that apply to the journal pertain.

show abstract

Section: Discussionmentioning

confidence: 99%

Characterization of gamma-ray irradiation influence on the corrosion behaviour of austenitic stainless steel

Aljohani

Geesi

Kaïba

et al. 2020

Materials Today Communications

View full text Add to dashboard Cite

show abstract

“…The experimental temperature also affects the tensile properties, however there is not a universal law for this. For example, Jones [ 28 ] reported the tensile properties varied with experimental temperature. However, Brnic [ 29 ] reported that when the experimental temperature was increased from 250 °C to 350 °C, the mechanical properties of 316L SS almost remained constant.…”

Section: Introductionmentioning

confidence: 99%

Stress Corrosion Behaviors of 316LN Stainless Steel in a Simulated PWR Primary Water Environment

Huang

Cong

et al. 2018

Materials

View full text Add to dashboard Cite

The effect of the strain rate, experimental temperature, Zn content in the test solution, and prefilming time on the mechanical properties was investigated by a tensile test with a slow strain rate, at a chemical solution of 2.2 ppm Li and 1200 ppm B in a static autoclave with 8.2 MPa. The experimental parameters clearly affected the tensile properties. The surface morphology, fractograph, and cross-sectional microstructure were analyzed by scanning electron microscopy and transmission electron microscopy. The δ (elongation) and UTS (ultimate tensile strength) of the samples tested in chemical solution were obviously lower than those of the samples tested under a nitrogen atmosphere. However, in general, all samples showed a ductile fracture characteristic and an excellent tensile property in all experimental conditions. The δ and UTS were first increased with increasing Zn content, and then decreased at both conditions of 9.26 × 10−7/s and 4.63 × 10−7/s strain rates. The difference values of tensile properties at different strain rates showed fluctuations with increasing Zn content. The δ increased with both increasing experimental temperature and prefilming time. The UTS first decreased with increasing prefilming time and then increased. The Iscc (stress corrosion cracking susceptibility) decreased with an increasing strain rate, experiment temperature, and prefilming time. Many particles with polyhedrons were formed on the sample surfaces, which was attributed to corrosion in a periodical location at the sample surface. The average length of the particles decreased with increasing Zn content, but increased with both increasing experimental temperatures and prefilming time. The corresponding mechanism is also discussed in this work.

show abstract

The effect of water radiolysis on the stress corrosion behavior of UNS S31600 stainless steel at 50 and 90°C

Wyllie

Steiner

Duquette

1996

Journal of Nuclear Materials

View full text Add to dashboard Cite

Effect of gamma irradiation on stress corrosion behavior of austenitic stainless steel under ITER-relevant conditions

Cited by 4 publications

References 3 publications

Characterization of gamma-ray irradiation influence on the corrosion behaviour of austenitic stainless steel

Characterization of gamma-ray irradiation influence on the corrosion behaviour of austenitic stainless steel

Stress Corrosion Behaviors of 316LN Stainless Steel in a Simulated PWR Primary Water Environment

The effect of water radiolysis on the stress corrosion behavior of UNS S31600 stainless steel at 50 and 90°C

Contact Info

Product

Resources

About