Drill wear monitoring in cortical bone drilling

Staroveški, Tomislav; Brezak, Danko; Udiljak, Toma

doi:10.1016/j.medengphy.2015.03.014

Cited by 44 publications

(33 citation statements)

References 20 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The drill bits used in the experiments were made of high-speed steel (HSS). In order to eliminate the effect of tool wear, it was replaced and a new drill bit was used for each experiment [32]. To measure the temperature during the drilling process, a k-type thermocouple was used in a depth of 3 mm and a 0.5-mm distance from the hole (Figure 2).…”

Section: Methodsmentioning

confidence: 99%

Modelling and optimisation of temperature and force behaviour in high-speed bone drilling

Sarparast

Ghoreishi

Jahangirpoor

et al. 2019

Biotechnology & Biotechnological Equipment

View full text Add to dashboard Cite

Bone drilling and implantation are important in orthopaedic surgery, dentistry and also fracture treatment. In many cases, due to the rise in temperature during bone drilling (higher than 47 C) and low conductivity of bone, thermal necrosis occurs. There is also risk of drill fracture due to the excessive thrust force. Despite many studies on the effect of different parameters on bone drilling temperature and force, there is still no clarity about the influence of the tool rotational speed and feed rate on the temperature and force responses. The aim of this study was to test and optimise the conditions in high-speed bone drilling, process force and temperature simultaneously. The results demonstrated that high-speed drilling is a suitable method for decreasing process temperature and force, and the rotational speed, feed rate and tool diameter were the most important factors in the high-speed bone drilling processes. Using a statistical method to model and optimise the process, a second-order model was developed to predict the behaviour of process temperature and thrust force in high-speed drilling. The optimised values were a rotational speed of 11778 rpm, feed rate of 50 mm/min and tool diameter of 2 mm, where the process force and temperature were 15.85 N and 33.4 C, respectively. Therefore, in high-speed bone drilling, the process thrust force and temperature decline, and the low effect of feed rate on temperature enables an increase in the speed of operation in robotic surgery.

show abstract

Section: Methodsmentioning

confidence: 99%

Modelling and optimisation of temperature and force behaviour in high-speed bone drilling

Sarparast

Ghoreishi

Jahangirpoor

et al. 2019

Biotechnology & Biotechnological Equipment

View full text Add to dashboard Cite

show abstract

“…That means it has to respect the pressure forces, speeds and feeds that can be achieved. Finally, we must achieve sufficient wear for pressure forces and torques to change [2,3].…”

Section: Methodsmentioning

confidence: 99%

“…Choice of cutting conditions and feeds were inspired by the available literature [2]. Our goal was to achieve the same circumferential speeds for all types of tested cutters, in different speed setups.…”

Section: Fig 1 Demonstration Of Power Drill Attachmentleft Axial Rimentioning

confidence: 99%

Evaluation of Wear of Milling Cutters for Drilling of Nail Holes Used for Osteosynthesis of Long Bones of Lower Limbs

Kubášová

Sedláček

Horny

2019

Strojnícky Časopis - Journal of Mechanical Engineering

View full text Add to dashboard Cite

This paper deals with wear of intramedullary milling cutters for the drilling of nail holes used for osteosynthesis of lower limbs long bones. After the physician’s complaints about the increasing resistance and total change of its properties that are caused by the reuse the instrument, we have designed a suitable methodology to verify and quantify this problem. The experiment was carried out on three types of milling cutters, differing in their diameter. Using statistical tests, we compared pressure force and torque before and after wear.

show abstract

“…Recently (Staroveski et al 2015) performed an experimental investigation on cortical bone to study the effect of tool wear on force and torque. They reported that temperature continuously increased using a repeated uses of drill bit.…”

Section: Introductionmentioning

confidence: 99%

“…Cutting forces (Alam et al 2009;Alam et al 2011;Wang et al 2014a) and torque (Alam et al 2011;Wang et al 2014a) should also be minimum. Using a drill bit repeatedly increased the temperature (Jochum and Reichart 2000;Allan et al 2005;Chacon et al 2006;Queiroz et al 2008;de Souza et al 2011;Oliveira et al 2012) and force (Staroveski et al 2015) significantly which may cause to decrease the strength of internal fixation (Allan et al 2005).…”

Section: Introductionmentioning

confidence: 99%

In-situ tool wear monitoring and its effects on the performance of porcine cortical bone drilling: a comparative in-vitro investigation

Gupta

Pandey

2017

Mech Adv Mater Mod Process

View full text Add to dashboard Cite

show abstract

Drill wear monitoring in cortical bone drilling

Cited by 44 publications

References 20 publications

Modelling and optimisation of temperature and force behaviour in high-speed bone drilling

Modelling and optimisation of temperature and force behaviour in high-speed bone drilling

Evaluation of Wear of Milling Cutters for Drilling of Nail Holes Used for Osteosynthesis of Long Bones of Lower Limbs

In-situ tool wear monitoring and its effects on the performance of porcine cortical bone drilling: a comparative in-vitro investigation

Contact Info

Product

Resources

About