Diffusion welding of SiCp/2014Al composites using Ni as interlayer

Feng, Tao; Chen, Xizhang; Wu, Lihui; Song-nian, Lou

doi:10.1016/s1005-8850(06)60056-x

Cited by 18 publications

(10 citation statements)

References 6 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…In addition, Wang et al [ 37 ] introduced the LFF into the FDM to realize the 3D difference calculation under the rolling condition of the wide plate rolling. Furthermore, Dr. Feng [ 38 ] incorporated the effect of tension on the width of the lateral flow zone, limit of shear stress with or without friction, and effect of the change in roll diameter on the lateral flow.…”

Section: A Survey Of Edc Theorymentioning

confidence: 99%

See 1 more Smart Citation

Development of Cold‐Rolling Edge‐Drop Control Technology for Electrical Steel: A Review

Wei

Wang

Sun

et al. 2023

steel research int.

View full text Add to dashboard Cite

As an emerging technology in the production of electrical steel, edge‐drop control (EDC) caters to the increasing requirements for the overall shape quality of strips. Herein this review, the development of EDC theory, method, and control system used in the cold‐rolling process is summarized. Also, in this review, research on EDC theory is found to be based on the 3D plastic deformation model of the strip, considering the lateral metal flow. Further, an analytical model and a numerical calculation method are employed to establish an edge‐drop calculation model with high accuracy and speed. Next, taper‐work‐roll shifting (T‐WRS), a conventional EDC technology, is found to have been greatly improved in actual production. However, T‐WRS technology involves coupling problems in terms of edge drop and crown and flatness control. Finally, the closed‐loop EDC is found to depend on the online WRS of multiple stands. Particularly, the genetic law of strip thickness in the continuous rolling process and the edge‐drop regulation characteristics of each stand in the continuous rolling mill are significant aspects; thus, a reasonable roll‐shifting control strategy must be formulated. Based on the reviewed research, the development prospect of EDC is characterized.

show abstract

Section: A Survey Of Edc Theorymentioning

confidence: 99%

“…The composition of the edge-drop deviation is analyzed into internal deviation, central deviation, and external deviation, and the WRS is determined according to the control characteristics of the three deviations of different stands. [38,79] Global optimal control…”

Section: Multipoint Controlmentioning

confidence: 99%

Development of Cold‐Rolling Edge‐Drop Control Technology for Electrical Steel: A Review

Wei

Wang

Sun

et al. 2023

steel research int.

View full text Add to dashboard Cite

show abstract

“…In order to overcome this problem, the researchers did a lot of work including fusion welding, 4,5 laser welding, 6 plasma arc in situ welding, 7 diffusion welding [8][9][10][11] and brazing 2,12,15 during the last 20 years. Brazing is considered the most promising welding method for Al-MMCs on account of its characterisation such as the shorter heating up time, the lower welding temperature and flexibility to the weldment.…”

Section: Introductionmentioning

confidence: 99%

Active brazing filler metal on SiC particle reinforced aluminium matrix composites

Wang

Cheng

et al. 2015

Science and Technology of Welding and Joining

View full text Add to dashboard Cite

The joints of aluminium matrix composites with high SiC particle content were achieved by vacuum brazing with Al-12Si-1?5Mg-4Ti foil as active filler. The effect of Ni coating and Ti on the wetting behaviour of filler metal on the composite was investigated. Owing to the presence of Ni coating, the wettability of liquid filler metal on the composite was enhanced obviously, and Ti(AlSi) 3 intermetallic is in situ strengthening phase in the seam. Sound joints with well appearance were obtained, and the optimised shear strength of the joint reached 109.3 MPa. Capable welding parameters were broadened by the presence of Ni coating and Al-12Si-1.5Mg-4Ti foil as filler for brazing of aluminium matrix composites with high SiC particle content.

show abstract

“…Solid state and transient liquid phase (TLP) diffusion bonding have been commonly used to join aluminum metal matrix composites. Feng et al (2006) have investigated solid state diffusion bonding of 2014Al/SiC metal matrix composite using Ni as interlayer with the thickness of 0.1 mm at 610 • C for 60 min. The bonding temperature of 610 • C may be considered as a high bonding temperature especially in diffusion bonding of Al/Mg 2 Si composites with low melting point.…”

Section: Introductionmentioning

confidence: 99%

Investigation on microstructure and mechanical properties of diffusion bonded Al/Mg2Si metal matrix composite using copper interlayer

Nami

Halvaee

Adgi

et al. 2010

Journal of Materials Processing Technology

View full text Add to dashboard Cite

Diffusion welding of SiCp/2014Al composites using Ni as interlayer

Cited by 18 publications

References 6 publications

Development of Cold‐Rolling Edge‐Drop Control Technology for Electrical Steel: A Review

Development of Cold‐Rolling Edge‐Drop Control Technology for Electrical Steel: A Review

Active brazing filler metal on SiC particle reinforced aluminium matrix composites

Investigation on microstructure and mechanical properties of diffusion bonded Al/Mg2Si metal matrix composite using copper interlayer

Contact Info

Product

Resources

About