Development Of Multiband MIMO Antenna With Defective Ground Structure: Review

Sarade, Shrenik Suresh; Ruikar, Sachin D.

doi:10.1016/j.procs.2020.04.196

Cited by 7 publications

(7 citation statements)

References 19 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Multiband MIMO antenna with defective ground structure was presented by Sarade and Ruikar [11] for review. Suggestions were made regarding general design approach to microstrip antenna.…”

Section: Review Of Related Literaturementioning

confidence: 99%

Comparative Design and Performance Analysis of Multiband MIMO Antenna for Sub-6 GHz 5G Network

Utahile,

Michael,

Jeffrey

2024

AJARR

View full text Add to dashboard Cite

This paper presents the design and performance comparison of a multiband dual diversity 8-element multiple-input multiple-output (MIMO) antenna with a 4-element MIMO antenna with defected ground structure (DGS) at 2.45/3.5/5.2/6 GHz. The proposed antennas were designed on a flame retardant (FR-4) having a dielectric constant of 4.4 , (\(\varepsilon\)r =4.4), dimensions of 200x200x1.6 mm 140x90x1.6 mm respectively. The antennas were simulated and analyzed using Computer Simulation Studio (CST Studio). Results obtained from the simulation showed that the 8-element MIMO antenna achieved a combined bandwidth of 908.68 MHz. In contrast, the 4-element MIMO antenna with DGS achieved 4.22 GHz bandwidth on average. Broadside radiation pattern was observed across the three frequency bands in both E- and H-plane with an average main lobe magnitude of 7.8 dBi. Furthermore, the proposed antennas achieved consistent Envelop Correlation Coefficient (ECC) and Diversity Gain (DG) values of 0.0008 and 9.999 and Port-to-port isolation of 27 dB across all frequencies considered. Also, an antenna gain of 8.58 dB was achieved at a frequency of 6 GHz for the 8-element MIMO antenna, while a maximum gain of 5.58 dBi was achieved by the 4-element MIMO antenna with DGS. The gain, isolation, DG, and ECC between adjacent ports and the loss in capacity were within the standard margins, making the antenna structure suitable for MIMO applications.

show abstract

“…Multiband MIMO antenna with defective ground structure was presented by Sarade and Ruikar [11] for review. Suggestions were made regarding general design approach to microstrip antenna.…”

Section: Review Of Related Literaturementioning

confidence: 99%

Comparative Design and Performance Analysis of Multiband MIMO Antenna for Sub-6 GHz 5G Network

Utahile,

Michael,

Jeffrey

2024

AJARR

View full text Add to dashboard Cite

show abstract

“…High data rates, bandwidth, channel capacity, data throughput, and less multi-path fading effects are fundamental requisites of the 5G technology, which cannot be met by the Single Input Single Output (SISO), and Single Input Multi Output (SIMO) systems (e.g., patch array antenna) [9][10][11][12][13][14][15][16][17] . Multi Inputs Multi Outputs (MIMO) technology is applied to solve these issues by providing multi-send and receive paths without increasing the input power 18 , which allows the 5G technology to maintain its reliability and coverage area.…”

Section: Introductionmentioning

confidence: 99%

Wideband High Gain Meatsurface-Based 2×2 MIMO antenna with Highly Isolated Ports for Sub-6 GHz 5G Applications

Salehi,

Oraizi

2024

Preprint

View full text Add to dashboard Cite

A high gain and wideband MIMO antenna with highly isolated ports allows the 5G technology to provide reliable wireless communication with high data rate, low latency, increased channel capacity, high signal quality, low power, and high data throughput while maintaining the penetration rate. This study presents the design and simulation of two wideband, high gain, metasurface-based 2 x 2 MIMO antennas operating from 2.85 to 4.2 GHz for 5G applications, which satisfy the 5G requisites. The radiating elements of the two MIMO antennas use the aperture coupled feeding technique with a dumbbell shape slot, a metasurface layer that utilizes the surface wave propagation, and a truncated square patch with two U-shaped slots to attain wideband and high gain performance. The power of the feed radiates through the dumbbell shape slot to illuminate the radiating patch, which allows better manipulation of the coupled power compared with the rectangular slot. The proposed MIMO structure places four identical radiating elements like a 2 x 2 matrix with a rotation of 0°, 90°, 180°, and 270° to produce orthogonal electromagnetic waves, which improves the isolation between ports. Two vertical and horizontal strip slots are engraved on the ground as the decoupling structure to decrease the mutual coupling among the radiating elements. Besides, the aperture-coupled feeding technique increases the independence between the radiating elements by isolating the radiating patches and the microstrip feed lines. The CST and HFSS software are used to simulate the antennas. According to the CST and HFSS simulation results, the highest gain values of the first MIMO design vary from 7.6 to 8.9 dBi and 8.8 to 9.25 dBi over the operational bandwidth, respectively. It achieves less than -32 dB isolation, almost 10 dB diversity gain, and below 0.0002 ECC. However, it experiences 2.2 to 5 dBi back lobe levels. The second MIMO antenna is proposed to kill the back lobe levels and increase the gain while providing high isolation and low mutual coupling. The second antenna put a metal plate at 20 mm beneath the first antenna to achieve peak gain values from 9.5 to 11.75 dBi, isolation below -20 dB, almost 10 dB diversity gain, and ECC (Envelope Correlation Coefficients) values below 0.0012 over 2.8 to 4.2 GHz. The achievements show that the radiating elements of both MIMO antennas work independently with minimal mutual coupling, which increases the channel capacity. The comparison with other studies' achievements indicates that the proposed MIMO antennas are among the best candidates for 5G based systems, such as IoT (Internet of Things) applications and vehicular communications.

show abstract

“…High data rates, broad bandwidth, increased channel capacity, high data throughput, and less multi-path fading effects are fundamental requisites of the 5G technology, which cannot be met by the Single Input Single Output (SISO), and Single Input Multiple Output (SIMO) systems (e.g., patch array antenna) [9][10][11][12][13][14][15][16][17] . Multiple Inputs Multiple Outputs (MIMO) technology is applied to solve these issues by providing multiple paths for sending and receiving data without increasing the input power 18 , which allows the 5G technology to maintain its reliability and coverage area.…”

Section: Introductionmentioning

confidence: 99%

Wideband High Gain Metasurface-Based 4T4R MIMO antenna with Highly Isolated Ports for Sub-6 GHz 5G Applications

Salehi,

Oraizi

2024

Preprint

View full text Add to dashboard Cite

This study presents the design of four 178×178 (mm)2 wideband, high gain, highly efficient metasurface-based 4T4R MIMO (Multiple-Input Multiple-Output) antennas with highly isolated ports, covering the middle and a portion of the upper bands of the sub 6 GHz 5G frequency spectrum for 5G-based systems, such as IoT (Internet of Things) applications, vehicular communications (e.g., rooftop antennas of cars or trains), smart industries (e.g., farms and factories). The radiating elements of these antennas use the aperture-coupled feeding technique with a dumbbell-shaped slot, a truncated square patch with two U-shaped slots, and a metasurface layer. The proposed MIMO structures place four identical radiating elements like a 2×2 matrix with 90o successive rotations to produce orthogonal electromagnetic waves, improving the isolation between ports. Six-millimeter spaces are added between these elements, and two vertical and horizontal strip slots are carved on the ground as the decoupling structure to decrease the mutual coupling. Simulation results show that Antenna_1, Antenna_2, and Antenna_3 achieve gain values of 6.2 to 9.4 dBi, 8.2 to 11.6 dBi, 6 to 9.5 dBi, below -35, -25, and -33 isolation and almost 10 dB diversity gain from 2.8 to 4.7 GHz, 2.8 to 4.5 GHz, and 2.7 to 4.9 GHz, respectively. As a prototype, Antenna_4 is manufactured, and measurements are performed. It achieves 6.28 to 10.45 dBi gain values, below -23 dB isolation, and 0.001 envelope correlation coefficient over 2.7 to 4.3 GHz. The results confirm that the proposed MIMO antennas are compatible with the 5G essential requisites.

show abstract

Development Of Multiband MIMO Antenna With Defective Ground Structure: Review

Cited by 7 publications

References 19 publications

Comparative Design and Performance Analysis of Multiband MIMO Antenna for Sub-6 GHz 5G Network

Comparative Design and Performance Analysis of Multiband MIMO Antenna for Sub-6 GHz 5G Network

Wideband High Gain Meatsurface-Based 2×2 MIMO antenna with Highly Isolated Ports for Sub-6 GHz 5G Applications

Wideband High Gain Metasurface-Based 4T4R MIMO antenna with Highly Isolated Ports for Sub-6 GHz 5G Applications

Contact Info

Product

Resources

About