Development of LabVIEW Program Using SR400 Gated Photon Counter for Continuous Data Acquisition and Analysis

Kapri, Rashtrapriya Kumar; Dwivedi, Rajeev; Dubey, P. K.; Sharma, Parag

doi:10.1007/s12647-021-00487-5

Cited by 2 publications

(2 citation statements)

References 52 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The hardware of the data acquisition system [8] mainly consists of sensors, data acquisition modules, IPCs and displays. The signal collected from the test site is transmitted to the sensor for conversion, and then transmitted to the IPC through signal conditioning.…”

Section: Software Design Of Electro-hydraulic Control System Based On...mentioning

confidence: 99%

Research on data processing module of electro-hydraulic control system based on motion control card

Zhou,

chen

2023

5th International Conference on Information Science, Electrical, and Automation Engineering (ISEAE 2023)

View full text Add to dashboard Cite

In the wind turbine drive chain test platform using hydraulic loading system to simulate the load on the wind turbine, so as to complete the fatigue test test of the key components of the wind turbine on the ground. The traditional method of using microcontroller or PLC as the core of the motion controller has been unable to meet the needs of modern society's high-precision industries, the new open motion controller based on PCI bus control has gradually developed into the mainstream of the market choice, PC and motion controller control mode is widely used in various industries of manufacturing. In this paper, LabVIEW software is selected as the control system development platform to study the implementation of the control method of Advantech's PCI motion control card, while the collected data is displayed and processed by a data acquisition card. According to the functional requirements, the human-machine interaction interface of the software is designed for data acquisition and storage. According to the interaction characteristics between modules, the detailed design and implementation of the back panel was carried out for different modules using different design modes.

show abstract

Section: Software Design Of Electro-hydraulic Control System Based On...mentioning

confidence: 99%

Research on data processing module of electro-hydraulic control system based on motion control card

Zhou,

chen

2023

5th International Conference on Information Science, Electrical, and Automation Engineering (ISEAE 2023)

View full text Add to dashboard Cite

show abstract

“…In addition, the program was utilised to develop a custom application software to monitor, control and record the data in real-time. LabVIEW consists of the function block and the front panel [10]. The function block is a graphical programming environment.…”

Section: Operating Softwarementioning

confidence: 99%

Design and construct unit to control fluid entering solar collectors during efficiency tests

Mezaal¹,

Alameri²

2022

J Appl Eng Science

View full text Add to dashboard Cite

This paper describes the development of an apparatus to control the fluids that enter a solar collector in experimental tests with respect to the Australian and New Zealand Standard AS/NZS 2535.1.2007. This standard explains the testing procedure, indicating that the inlet fluid should have specified temperature and flow rate uncertainties. The hardware components were constructed in the lab. A new sophisticated data acquisition system with an NI CompactDAQ was added to control the unit, and a new software application in LabVIEW was developed. The unit was operated in an open-loop to understand its behaviour as a multiple-inputs and multiple-outputs system (MIMO). A rule of thumb tuning method was used to design the proportional-integral PI controller for the heating system.Moreover, a custom decoupler with a PI controller was developed to reduce the interactions in the MIMO. The measured steady-state responses were analysed to determine the flow rate and temperature compared with the limited boundaries. The final results show that the system could supply water to the solar collector within the accuracy requirements. Achieving the fluid's absolute temperature and flow rate within the required constraints of the published standard has proven that the developed unit can be adapted to perform solar collector testing. However, additional steps are suggested for further work to enable the unit to provide field testing.

show abstract

Development of LabVIEW Program Using SR400 Gated Photon Counter for Continuous Data Acquisition and Analysis

Cited by 2 publications

References 52 publications

Research on data processing module of electro-hydraulic control system based on motion control card

Research on data processing module of electro-hydraulic control system based on motion control card

Design and construct unit to control fluid entering solar collectors during efficiency tests

Contact Info

Product

Resources

About